Working Advice; Sawing Wood; Maintenance And Cleaning - Würth 5700 103 Serie Manual De Instrucciones

Switching on the LED Work Area Illumi-
nation
The power light 26 lights up when the On/Off switch 4 is
slightly or completely pressed, and allows the work area to be
illuminated when lighting conditions are insufficient.

Working Advice

Protect saw blades against impact and shock.
Guide the machine evenly and with light feed in the cutting
direction. Excessive feed significantly reduces the service life
of the saw blade and can cause damage to the power tool.
Sawing performance and cutting quality depend essentially
on the condition and the tooth form of the saw blade. There-
fore, use only sharp saw blades that are suited for the material
to be worked.

Sawing Wood

The correct selection of the saw blade depends on the type
and quality of the wood and whether lengthway or crossway
cuts are required.
When cutting spruce lengthways, long spiral chips are
formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
Sawing with Parallel Guide
(see figure D)
The parallel guide 32 enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Set the desired cutting width at the outer edge of the base
plate using the scale on the guides of the parallel
guide/guide rail adapter. (see figure D)
Sawing with Guide Rail (see figure E)
The guide rail 34 is used to carry out straight cuts.
Note: Use the guide rail 34 only for right-angled cuts. When
using for mitre cuts, the guide rail 34 can become damaged.
The adhesive coating prevents the guide rail from slipping
and protects the surface of the workpiece. The coating of the
guide rail allows the circular saw to glide easily.
Fasten the guide rail 34 to the workpiece using suitable
clamping devices, e.g. screw clamps. Put the power tool with
mounted guide rail adapter on the guide rail.
The guide rail 34 must not extend beyond the face
side of the workpiece where the cut is to be
started.
Switch the machine on and guide it in the cutting direction
applying moderate and steady feed.
Working with parallel guide/guide rail
adapter and vacuum hose
First mount the extraction adapter 29 with vacuum hose 30
and then the parallel guide/guide adapter 32.
Note: Use only the intended screws to fix the parallel
guide/guide adapter 32 and the extraction adapter 29!
Sawing with Auxiliary Guide
(see figure F)
For sawing large workpieces or straight edges, a board or
strip can be clamped to the workpiece as an auxiliary guide;
the base plate of the circular saw can be guided alongside
the auxiliary guide.
Recommendations for Optimal
Handling of the Battery
Protect the battery against moisture and water.
Store the battery only within a temperature range between
–20 °C and 50 °C. As an example, do not leave the bat-
tery in the car in summer.
Occasionally clean the venting slots of the battery using a
soft, clean and dry brush.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.

Maintenance and Cleaning

 Before any work on the machine itself (e. g.
maintenance, tool change, etc.) as well as dur-
ing transport and storage, remove the battery
from the power tool. There is danger of injury when
unintentionally actuating the On/Off switch.
 For safe and proper working, always keep the
machine and ventilation slots clean.
The retracting blade guard must always be able to move
freely and retract automatically. Therefore, always keep the
area around the retracting blade guard clean. Remove dust
and chips by blowing out with compressed air or with a brush.
Saw blades that are not coated can be protected against cor-
rosion with a thin coat of acid-free oil. Before use, the oil must
be removed again, otherwise the wood will become soiled.
Resin and glue residue on the saw blade produces poor cuts.
Therefore, clean the saw blade immediately after use.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
a Würth master-Service.
23