Tool Specifications; Ec Declaration Of Conformity; Noise/Vibration Information; Battery Charging - Würth 5700 103 Serie Manual De Instrucciones

Tool Specifications

Cordless circular saw
Art. No.
Rated voltage
No-load speed
Cutting depth, max.
– for 0° bevel angle
– for 45° bevel angle
Spindle lock
Base plate dimensions
Saw blade diameter, max.
Saw blade diameter, min.
Blade thickness, max.
Tooth thickness/setting, max.
Tooth thickness/setting, min.
Mounting bore
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
1)
– during operation and during
storage
Recommended batteries
Recommended chargers
1) Limited performance at temperatures <0 °C

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-5.
Typically the A-weighted noise levels of the product are:
Sound pressure level 90 dB(A); Sound power level
101 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
determined according to EN 60745:
Cutting wood: a =2.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or insertion tools or
is poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
HKS 10-A
5700 103 X
V=
-1
min
mm
mm
mm
mm
mm
mm
mm
mm
mm
kg
°C
°C
0700 996 2XX
0700 896 XXX
(triax vector sum) and uncertainty K
2 2
, K=1.5 m/s .
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
10.8
sories, keep the hands warm, organisation of work patterns.
1400
26.5
EC-Declaration of Conformity
17.0

We declare under our sole responsibility that the product
167 x 88
described under "Tool Specifications" is in conformity with all
85
relevant provisions of the directives 2009/125/EC (Regula-
85 tion 1194/2012), 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
0.7
the following standards: EN 60745-1, EN 60745-2-5.
1.1
Technical file (2006/42/EC) at:
1.0
Adolf Würth GmbH & Co. KG, Abt. PCM,
15
Reinhold-Würth-Straße 12–17
74653 Künzelsau, Germany
1.4
0...+45
–20...+50
Marcel Strobel
General Manager
Künzelsau: 31.08.2014
 Use only the chargers listed in the tool specifi-
cations. Only these chargers are matched to the lithium-
ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch
after the machine has been automatically
switched off. The battery can be damaged.
Observe the notes for disposal.
Dr.-Ing. Siegfried Beichter
General Manager

Battery Charging

20