Disposal Information; Declaration Of Conformity; Exemption From Liability - Flex LST 803 VR Instrucciones De Funcionamiento Originales

Bush hammering machine LST 803 VR, LST 1503 VR
Cleaning
Regularly clean the power tool and ventilation
slots. Frequency of cleaning is dependent
on the material and duration of use.
Regularly blow out the housing interior and
motor with dry compressed air.
Carbon brushes
The electric power tool features cut-off carbon
brushes.
When the cut-off carbon brushes reach their
wear limit, the electric power tool switches
off automatically.
klqb
rëÉ=çåäó=çêáÖáå~ä=é~êíë=ëìééäáÉÇ=Äó=íÜÉ=ã~åìJ
Ñ~ÅíìêÉê=Ñçê=êÉéä~ÅÉãÉåí=éìêéçëÉëK=
fÑ=åçåJçêáÖáå~ä=é~êíë=~êÉ=ìëÉÇI=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=ïáää=ÄÉ=ÇÉÉãÉÇ=
åìää=~åÇ=îçáÇK
When the power tool is being used, the carbon
brushes can be seen sparking through the rear
air inlet apertures.
If the carbon brushes are sparking excessively,
switch off the electric power tool immediately.
Take your electric power tool to a customer
service centre authorised by the manufacturer.
Gears
klqb
aç=åçí=äççëÉå=íÜÉ=ëÅêÉïë=çå=íÜÉ=ÖÉ~ê=ÜÉ~Ç=
ÇìêáåÖ=íÜÉ=ï~êê~åíó=éÉêáçÇK=
kçåJÅçãéäá~åÅÉ=ïáää=ÇÉÉã=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=åìää=~åÇ=îçáÇK
Repairs
Repairs may be carried out by an authorised
customer service centre only.
Spare parts and accessories
Exploded drawings and spare-part lists can
be found on our homepage:
www.flex-tools.com

Disposal information

t^okfkd>
oÉåÇÉê=êÉÇìåÇ~åí=éçïÉê=íççäë=ìåìë~ÄäÉ=
Äó êÉãçîáåÖ=íÜÉ=éçïÉê=ÅçêÇK
EU countries only
Do not throw electric power tools
into the household waste!
In accordance with the European
Directive 2012/19/EC on Waste Electrical
and Electronic Equipment and transposition
into national law used electric power tools
must be collected separately and recycled in
an environmentally friendly manner.
klqb
mäÉ~ëÉ=~ëâ=óçìê=ÇÉ~äÉê=~Äçìí=Çáëéçë~ä=çéíáçåë>

-Declaration of Conformity

We declare under our sole responsibility that
the product described under "Technical
specifications" conforms to the following
standards or normative documents:
EN 60745 in accordance with the regu-
lations of the directives
2004/108/EC (until 19.04.2016),
2014/30/EU (from 20.04.2016),
2006/42/EC, 2011/65/EC.
Responsible for technical documents:
FLEX-Elektrowerkzeuge GmbH, R & D
Bahnhofstrasse 15, D-71711 Steinheim/Murr
Eckhard Rühle
Manager Research &
Development (R & D)
29.05.2015
FLEX-Elektrowerkzeuge GmbH
Bahnhofstrasse 15, D-71711 Steinheim/Murr

Exemption from liability

The manufacturer and his representative are
not liable for any damage and lost profit due to
interruption in business caused by the product
or by an unusable product.
The manufacturer and his representative are
not liable for any damage which was caused by
improper use of the power tool or by use of the
power tool with products from other
manufacturers.
Klaus Peter Weinper
Head of Quality
Department (QD)
21