Disposal Information; Declaration Of Conformity; Exemption From Liability - Flex L 3403 VRG Instrucciones De Funcionamiento Originales

Polisher L 3403 VRG
Carbon brushes
The polisher features cut-off carbon brushes.
When the wear limit of the cut-off carbon
brushes is reached, the polisher switches off
automatically.
klqb
rëÉ=çåäó=çêáÖáå~ä=é~êíë=ëìééäáÉÇ=Äó=íÜÉ=
ã~åìÑ~ÅíìêÉê=Ñçê=êÉéä~ÅÉãÉåí=éìêéçëÉëK=
fÑ åçåJçêáÖáå~ä=é~êíë=~êÉ=ìëÉÇI=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=ïáää=ÄÉ=ÇÉÉãÉÇ=
åìää=~åÇ=îçáÇK
When the polisher is being used, the carbon
brushes can be seen sparking through the rear
air inlet apertures.
If the carbon brushes spark excessively,
switch off the polisher immediately. Take the
polisher to a customer service workshop
authorised by the manufacturer.
Gears
klqb
aç=åçí=äççëÉå=íÜÉ=ëÅêÉïë=çå=íÜÉ=ÖÉ~ê=ÜÉ~Ç=ERF=
ÇìêáåÖ=íÜÉ=ï~êê~åíó=éÉêáçÇK=
kçåJÅçãéäá~åÅÉ=ïáää=ÇÉÉã=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=åìää=~åÇ=îçáÇK
Repairs
Repairs may be carried out by an authorised
customer service centre only.
Spare parts and accessories
For other accessories, in particular tools
and polishing aids, see the manufacturer's
catalogues.
Exploded drawings and spare-part lists
can be found on our homepage:
www.flex-tools.com

Disposal information

t^okfkd>
oÉåÇÉê=êÉÇìåÇ~åí=éçïÉê=íççäë=ìåìë~ÄäÉ=
Äó êÉãçîáåÖ=íÜÉ=éçïÉê=ÅçêÇK
EU countries only
Do not throw electric power tools
into the household waste!
In accordance with the European Directive
2012/19/EC on Waste Electrical and
Electronic Equipment and transposition into
national law used electric power tools must
be collected separately and recycled in an
environmentally friendly manner.
klqb
mäÉ~ëÉ=~ëâ=óçìê=ÇÉ~äÉê=~Äçìí=Çáëéçë~ä=çéíáçåë>

-Declaration of Conformity

We declare under our sole responsibility
that the product described under "Technical
specifications" conforms to the following
standards or normative documents:
EN 60745 in accordance with the regu-
lations of the directives
2004/108/EC (until 19.04.2016),
2014/30/EU (from 20.04.2016),
2006/42/EC, 2011/65/EC.
Responsible for technical documents:
FLEX-Elektrowerkzeuge GmbH, R & D
Bahnhofstrasse 15, D-71711 Steinheim/Murr
20.07.2015
FLEX-Elektrowerkzeuge GmbH
Bahnhofstrasse 15, D-71711 Steinheim/Murr

Exemption from liability

The manufacturer and his representative are
not liable for any damage and lost profit
due to interruption in business caused
by the product or by an unusable product.
The manufacturer and his representative are
not liable for any damage which was caused
by improper use of the power tool or by use
of the power tool with products from other
manufacturers.
19