DeVilbiss 702576 Boletín Técnico

Technical Bulletin
702576 Aluminium Gravity Feed Cup (900cc)
Important: Before using this equipment,
read all safety precautions and instruc-
tions. Keep for future use.
WARNING
Halogenated Hydrocarbon Solvents —
for example: 1,1,1,-Trichloroethane and
methylene chloride can react with the
aluminium in this cup and cause an
explosion hazard. Read the data sheet
for the material you intend to spray. Do
not use spray materials containing these
solvents with this cup.
DESCRIPTION
The cup is constructed from durable
aluminium to provide trouble-free operation.
The cup insert is electroless nickel
plated brass. The disposable cup lid is
recyclable and is constructed with recycled
polyethylene. The lid has a unique drip
check to prevent paint from dripping out of
the vent in the lid.
ASSEMBLY OF CUP TO GUN
1. Place filter (3) in cup outlet, if desired.
See cup drawings.
2. Place cup gasket (4) in the fluid inlet
of the gun body, if desired. See cup
drawings.
3. Assemble cup to gun and tighten hand
tight.
FILLING WITH PAINT
Fill the cup with paint to within 20mm (3/4")
from the top. Do not overfill.
INSTALLING THE LID
Place plastic lid on the top of the cup, and
push in the centre of the lid to assemble
lid. Fold vent cap and push onto centre
portion of lid (if vent cap is not already
assembled).
DeVilbiss Automotive Refinishing
DeVilbiss has authorized distributors throughout the world.
For equipment, parts and service, check the Yellow Pages
under "Automotive Body Shop Equipment and Supplies."
For technical assistance, see listing below.
U.S.A./Canada Customer Service Office:
11360 S. Airfield Road, Swanton, OH 43558
Toll-Free Telephone: 1-800-445-3988 (U.S.A. and Canada only)
Toll-Free Fax: 1-800-445-6643
CLEANING
NOTE
For routine cleaning, it is not
necessary to remove cup from
gun.
CAUTION
Do not soak the lid in
solvent for extended periods
of time. Doing so could
cause cup/lid sealing
problems and leakage.
The cup lid is designed to be disposable
but may be cleaned and reused if slightly
contaminated with overspray. If lid
becomes tight, or does not fit, it is due
to extended soaking in solvent. Let lid air
dry overnight and the lid should return to
its original size and fit.
Remove lid and properly dispose of any
excess paint. Pour in a small amount of
clean solvent. The amount will vary with
different coatings and solvents. Reinstall
lid. Shake cup to wash down the inside
surfaces. Hold lid while shaking to
prevent lid from coming off. Pull trigger to
allow some solvent to be flushed through
gun. Remove lid and pour out dirty solvent.
Add a small amount of clean solvent and
repeat procedure. Wipe exterior of lid with a
clean cloth and clean solvent.
If a paint filter was used in the bottom of
the cup outlet, it should be removed and
cleaned or replaced at this time. Dispose
of used cup lid if contaminated and replace
with new.
CUP DRAWINGS
Filter (3)
2
1
3
4
Parts List
REF NO. REPLACEMENT PART NO.
1 702576
2 GFC-404-K2
3 KGP-5-K5
4 KGP-13-K5
9/14 © 2014 DeVilbiss Automotive Refinishing. All rights reserved.
TB-1003-E
Replaces TB-1003-D
Cup Fitting
Cup Gasket (4)
Gun Body
DESCRIPTION
Metal Gravity Feed Cup (900cc)
Disposable Lid Kit (Kit of 2)
Filter Kit (Kit of 5)
Cup Gasket (Blue) (Kit of 5)