Setting (Individual) Day Program P6; Setting 7D Week Program (Individual); Timer Operating Mode - Bosch Heat Convector 4000 Manual Del Usuario

Duration 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Operation
mode
Table 60 Program P5
P5 is the recommended predefined program for continuous operation in the ECO operating mode.

4.5.5 Setting (individual) day program P6

If the week day and time were previously set, the day program
P6 has already been selected and the first two action steps can
be omitted.
To set the day program P6:
▶ Call up the parameter settings menu
( Chapter 4.3.1, page 59).
▶ Call up the day program settings menu (P6)
( Chapter 4.3.2, page 60).
P6/no flashes on the display.
▶ Press the or key until P6/go appears.
▶ Press the key to confirm P6/go.
00/Ec flashes on the display.
00 stands for the hours and Ec stands for the operating
mode ECO.
Duration 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Operation
mode
Table 61 Program P6 (can be adjusted individually)
P6 has the predefined settings of program P1 (operating mode
ECO:22:00...06:00 Clock and 08:00...18:00 Clock; heating
mode operating mode: 06:00...08:00 Clock and
18:00...22:00 o'clock).

4.5.6 Setting 7d week program (individual)

If the day program P6 was previously set, the 7d week program
is already selected and the first two action steps can be
omitted.
To set the 7d week program:
▶ Call up the parameter settings menu
( Chapter 4.3, page 59).
▶ Call up the settings menu for the 7d week program
( Chapter 4.3.2, page 60).
7d/no flashes on the display.
▶ Press the or key until 7d/go appears.
▶ Press the key to confirm 7d/go.
d1/P1 flashes on the display.
d1 stands for the day of the week and P1 stands for the
program that has been preset for this day.
▶ Press the or key to change the program from P1 to
P6.
Heat Convector 4000 – 6720883017 (2020/05)
▶ Press the or key to change the Ec (ECO) operating
mode to Co (heating mode).
▶ Press the key to confirm the set operating mode for the
hour displayed.
01/Ec flashes on the display.
▶ Repeat the operation for every hour from 0 to 23.
After the last hour has been set (23), P6/no flashes on the
display.
▶ Press the key to confirm the day program P6.
The week program (7d) appears on the display.
The table shows the predefined settings of the day program P6.
▶ Press the key to confirm the program that has been set
for the day of the week shown.
d2/P1 flashes on the display.
▶ Repeat procedure for every day of the week from d1 to d7.
After the last day has been set (d7), 7d/no flashes on the
display.
▶ Press the key to confirm the 7d week program.
The Window open function appears on the display.
The table shows the predefined settings of the 7d week
program. A day program (P1 to P6) can be assigned to each day
of the week.
Day d1 d2
Program P1 P1
Table 62 7d week program (can be adjusted individually)

4.5.7 TIMER operating mode

The set program can be changed (overwritten) for up to 8 hours
in the Timer operating mode. Once the timer time has expired,
the convector reverts to the set program.
The default setting is 1 hour.
Operation
d3 d4 d5 d6
P2 P1 P1 P3
d7
P3
63