Pentair MASTER PLUMBER 540072 Manual Del Usuario página 3

Installation / Operation
INSTALLATION
Hazardous voltage. Can shock, burn or
cause death. Do not use power cord to lift
motor. Always use the handle.
1. Pump should be located and should rest on level
solid foundation. Do not suspend pump by means of
discharge pipe or power cord. Keep pump inlet screen
clear.
2. Use a standard 3/4" garden hose or a 1" ID hose for the
side discharge.
NOTICE: To keep friction as low as possible, hose must
be 3/4" or larger. Keep the hose as short as
possible.
3. If, in your application, backflow is a problem when the
pump stops, prevent it by installing a 1" NPT check valve
in the pump discharge pipe.
4. Power Supply: Pump is designed for 115V., 60 HZ.
operation and requires an individual branch circuit of 15
amperes or more capacity. It is supplied with a 3-wire
cord set with grounding-type plug for use in a 3-wire,
grounded outlet. A 3 wire extension cord, of at least
14 AWG (2mm ) size is suggested, with larger sizes for
2
runs over 25 ft (7M). For safety, the pump should always
be electrically grounded to a suitable electrical ground
such as a grounded water pipe or a properly grounded
metallic raceway, or ground wire system. Do not cut off
the round grounding prong.
Personal injury. The pump motor is
equipped with automatic resetting
thermal protector and may restart unexpectedly. The
protector tripping is an indication of motor overloading
as a result of operating pump at low heads (low
discharge re striction), excessively high or low voltage,
inadequate wiring, incorrect motor connections, or a
defective motor or pump.
* Lake Chemical Co., Chicago, Illinois
Master Plumber warrants to the original consumer purchaser ("Purchaser") of its products that they are free from defects in material or workmanship.
If within twenty-four (24) months from the date of the original consumer purchase any such product shall prove to be defective, it shall be repaired or replaced at Master Plumber's option, subject to the
terms and conditions set forth below. Your original receipt of purchase is required to determine warranty eligibility.
Exceptions to the Twenty-four (24) Month Warranty
Product
Drill Pump
MiniVac Pump, 12 Volt MiniVac Pump
Model 540136 Submersible Sump Pump
General Terms and Conditions
Purchaser must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole
judgement of MASTER PLUMBER, have been subject to negligence, abuse, accident, misapplication, tampering, alteration; nor due to improper installation, operation, maintenance or storage; nor to
other than normal application, use or service, including but not limited to, operational failures caused by corrosion, rust or other foreign materials in the system, or operation at pressures in excess of
recommended maximums.
Requests for service under this warranty shall be made by returning the defective product to the Retail outlet or to Master Plumber as soon as possible after the discovery of any alleged defect.
Master Plumber will subsequently take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than 30 days after the term
of the warranty.
This warranty sets forth MASTER PLUMBER's sole obligation and purchaser's exclusive remedy for defective products.
MASTER PLUMBER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICABLE EXPRESS WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
OPERATION
motor with wet hands or when standing on wet or damp
surface, or in water. Disconnect power from pump before
handling or servicing pump.
This pump will continue to run until it is unplugged.
NOTICE: When you plug the pump into the wall
outlet, it will operate continuously, whether partly or fully
submerged.
1. The motor is equipped with an automatically resetting
2. The water being pumped cools the motor, allowing the
MAINTENANCE
A clogged inlet can reduce the pump's performance. A
clogged inlet screen can usually be cleaned out by back
flushing with a garden hose through the pump's discharge
pipe.
Master Plumber Limited Warranty
®
Master Plumber Pump • Chicago, IL 60631
Phone: 1-800-628-9439 • Web: www.masterplumberpump.com
Hazardous voltage. Can shock, burn or
cause death. Do not handle pump or pump
thermal overload protector. If the motor gets too hot,
the overload protector will stop the motor before it is
damaged. When the motor has cooled sufficiently, the
overload protector will reset itself and the motor will
restart.
NOTICE: If the overload protector stops the pump
repeatedly, disconnect the power from the pump and
check it to find the problem. Low voltage, long extension
cords, clogged impeller, too much back pressure in the
discharge hose (as when pumping through 50' (15 M) of
coiled hose), or extended running of pump with no load,
can all cause overheating.
pump to run continuously at any depth of water above
3/8". However, if the motor overload stops the pump,
allow it to cool for one hour before restarting. Motor will
not restart before the overload has cooled.
3
Warranty Period
90 days
One Year
Lifetime