Explanation Of General View; Specific Safety Rules - Makita 5603R Manual De Instrucciones

ENGLISH
(Original instructions)
1 A typical illustration of proper
hand support, workpiece sup-
port, and supply cord routing (if
applicable).
2 To avoid kickback, do support
board or panel near the cut.
3 Do not support board or panel
away from the cut.
4 Lever
5 Clamping screw
6 Base plate
7 Top guide
SPECIFICATIONS
Model
Blade diameter
at 90°
Max.
cutting depth
at 45°
-1
No load speed (min
Overall length
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to circular saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
Danger:

Explanation of general view

8 Base
9 60° angle cuts
10 45° angle cuts
11 30° angle cuts
12 Straight cuts
13 Blade
14 Setting protuberances
15 Hex socket head bolt
(For adjusting riving knife)
16 Cutting depth
17 Lock-off button
18 Switch trigger
5603R 5703R
165 mm 190 mm
54 mm 66 mm
38 mm 46 mm
) 5,000
330 mm 356 mm
4.9 kg 5.7 kg
/II
5705R
190 mm
66 mm
46 mm
4,800 4,800
356 mm
5.7 kg
/II /II
1. Keep hands away from cutting area and the
blade. Keep your second hand on auxiliary han-
dle, or motor housing. If both hands are holding
the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece. Do not attempt to remove cut material
when blade is moving.
CAUTION: Blades coast after turn off. Wait until
blade stops before grasping cut material.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
GEA010-1
control. (Fig. 1)
5. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and shock the
operator.
6. When ripping always use a rip fence or straight
edge guide. This improves the accuracy cut and
GEB029-1
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
19 Hex wrench
20 Shaft lock
21 Hex socket head bolt
22 Outer flange
23 Saw blade
24 Inner flange
25 Vacuum cleaner
26 Limit mark
27 Screwdriver
28 Brush holder cap
5903R 5103R
235 mm 270 mm
85 mm 100 mm
64 mm 73 mm
4,500 3,800
400 mm 442 mm
7.2 kg 9.4 kg
/II /II
5143R
355 mm
130 mm
90 mm
2,700
607 mm
14.0 kg
/II
5