Bosch PCM 7 S Manual Original página 23

21 Laser on/off switch (for marking of cutting line)
22 Chip ejector
23 Mounting holes for material clamp
24 Transport handle
25 Hex key (6 mm)
26 Locking screw for slide device
27 Recessed handles
28 Opening for saw-table extension
(on saw table base)
29 Transport safety-lock
30 Spindle lock
31 Battery compartment
32 Opening for saw-table extension
(on the second saw-table extension)
33 Hex socket screw (size 6 mm) for mounting of saw blade
34 Clamping flange
35 Interior clamping flange
36 Saw blade
37 Wing bolt
38 Threaded rod
39 Indicator for bevel angle
40 Scale for bevel angle
41 Slide device
42 Casing stop for depth stop
43 Screws for insert plate
44 Laser beam outlet
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Sliding Mitre Saw
Article number
Rated power input
No-load speed
Laser type
Laser class
Weight according to
EPTA-Procedure 01/2003
Protection class
Permissible workpiece dimensions (maximal/minimal) see page 26.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Bosch Power Tools
PCM 7 S
3 603 M01 3..
W 1200
-1
min 4800
nm 650
mW < 1
2
kg 11.8
/II
mm 190
mm 1.4–2.5
mm 30
Noise/Vibration Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 94 dB(A); Sound power level
107 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029:
2
a <2.5 m/s , K=1.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards:
EN 61029-1, EN 61029-2-9, EN 60825-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 23.07.2014
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
English | 23
2
.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 0VM | (23.7.14)