Assembly; Battery Cable Connection (Electric Start Only); Add Engine Oil - Generac GP Serie El Manual Del Propietario

Ocultar thumbs Ver también para GP Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Hardware Bag
Cotter Pin (F)
Plastic Spacer (G)
Locking Flange Nut (H)
Hex Head Bolt (J)
Lock Washer (K)
Flat Washer (L)
Capscrew (5/16 x 1) (M)
Capscrew (5/16 x 2-1/2) (N)
3. Call Generac Customer Service 1-888-
GENERAC (1-888-436-3722) with the unit
model and serial number for any missing
carton contents.
4. Record model, serial number, and date of
purchase on front cover of this manual.

Assembly

Consult Manual. Read and understand manual
completely before using product. Failure to
completely understand manual and product
could result in death or serious injury.
Call Generac Customer Service at 1-888-
GENERAC (1-888-436-3722) for any assem-
bly issues or concerns. Please have model
and serial number available.
The following tools are required to install the
accessory kit.
• Needle nose pliers
• 9/16" and 1/2" socket
• 1/2" wrench
NOTE: The wheels are not intended for over-
the-road use.
See
Figure
2-10.
Install wheels as follows:
1. Slide axle (D) through the flat washer (L),
plastic spacer (G), wheel (B), and axle
bracket assembly (E) on frame.
2. Insert cotter pin (F) through axle (D). Bend
tabs (of cotter pins) outward to lock into
place.
3. Install locking flange nut (H).
Install frame foot assembly as follows:
1. Slide hex head bolts (J) through holes in
frame rail.
2. Slide frame foot (C) onto hex head bolts
(J). Install locking flange nut (H).
3. Slide capscrew (M) through frame foot
assembly (C). Install lock washer (K), flat
washer (L) and locking flange nut (H).
Install handle as follows:
1. Slide capscrew (N) through flat washer (L),
handle (A) and frame. Install flat washer
(L) and locking flange nut (H).
8
WARNING
(000100a)
.
Qty.
2
1
N
6
6
2
6
2
2
A
Figure 2-10. Wheel & Handle Assembly
Battery Cable Connection
(electric start only)
The unit has been shipped with the battery
cables disconnected.
You will need two 8mm box wrenches to con-
nect the battery cables. See
1. Cut off cable ties securing battery cables
and remove red cover from battery termi-
nal.
2. First, connect the red cable to the positive
(+) battery terminal with the bolt and nut
supplied.
3. Make sure connections are secure and
slide rubber boot over the positive (+) bat-
tery terminal and connection hardware.
4. Connect the black cable to the negative (-)
battery terminal with the bolt and nut sup-
plied. Slide rubber boot over the negative
(-) battery terminal and connection hard-
ware.
5. Make sure all connections are secure.
NOTE: If the battery is unable to start the
engine, charge it with the 12V charger
included in the accessory box (see the
the 12 VDC Battery Charger
details).

Add Engine Oil

Engine damage. Verify proper type and quantity of
engine oil prior to starting engine. Failure to do so
could result in engine damage.
1. Place generator on a level surface.
2. Verify oil fill area is clean.
3. Remove oil fill cap and wipe dipstick clean.
See
Figure
H
L
L
C
H
CAUTION
2-11.
Owner's Manual for Portable Generator
E
G
B
L
F
J
M
000925
D
L
K
Figure
4-5.
Using
section for
(000135)

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido