Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
"P" wil be displayed on the power
indicator (5).
The power can be disconnected by
pressing the sensor (3)
sensors
(3) y
(4) together.
The Power function has a maximum
duration specified in Table 2. After this
time, the power level will automatically
adjust to 9. A beep sounds.
On activating the Power function in
one hotplate, it is possible that the
performance of some of the others
may be affected, reducing its power to
a lower level, in which case this will be
displayed on its indicator (3).
The power can be disconnected by
pressing the sensor (3)
sensors
(3) y
(4) together.
Power Management function
(depending on model)
Some models are equipped with
a power limiting function (Power
Management). This function allows
the total power generated by the hob
to be set to different values selected by
the user. To do this, for the first minute
after having connected the hob to the
power supply, it is possible to access
the power limiting menu.
1 With the cooktop in off state, press
together the sensors
during 3 seconds.
2 After 3 seconds it will be shown
"PL" in the displays. To enter
in the selection menu for power
limitation, press button
3 With sensors
(9) and
limit power value can be selected.
4 Once the value has been selected
(see Table 1), press the sensor
(8). The cooktop will be limited to
the chosen value.
Table 1
Value
or the
(
), nL
25
30
35
40
45
50
55
60
If you want to change the value again,
you must unplug the hob and plug it in
or the
again after a few seconds. Thus you
will again be able to enter the power
limiting menu.
Every time the power level of a
hotplate is changed, the power limiter
will calculate the total power the hob
is generating. If you have reached the
total power limit, the touch control will
not allow you to increase the power
level of that hotplate. The hob will beep
and the power indicator (5) will blink
at the level that cannot be exceeded.
If you wish to exceed that value, you
must lower the power of the other
hotplates. Sometimes it will not be
enough to lower another by a single
level as this depends on the power of
each hotplate and the level it is set at.
It is possible that to raise the level of
(7) y
(8),
a large hotplate that of several smaller
ones must be turned down.
If you use the quick switch-on at
maximum power function and the
said value is above the value set by
(8).
the limit, the hotplate will be set to the
maximum possible level. The hob will
(10) the
beep and the said power value will
blink twice on the indicator (5).
Safety switch off function
If due to an error one or several
heating zones do not switch off, the
appliance will be automatically discon-
nected after a set amount of time (see
table 2).
Table 2
Power
Selected
power
level
no limit
0
2,5 kW
1
3 kW
2
3,5 kW
3
4 kW
4
4,5 kW
5
5 kW
6
5,5 kW
7
6 kW
8
9
P
When the "safety switch off" function
has been triggered, a 0is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Keep the control panel of the
heating areas clean and dry at all
times.
In the event of operating pro-
blems or incidents not mentioned
in this manual, disconnect the
appliance and contact the TEKA
technical service.
Suggestions and
recommendations
* Use pots or pans with thick, comple-
tely flat bottoms.
* Do not slide pots and pans over the
glass because they could scratch it.
* Although the glass can take knocks
from large pots and pans without
sharp edges, try not to knock it.
* To avoid damaging the ceramic
glass surface, do not drag pots
and pans over the glass and keep
the undersides of them clean and
in good condition.
* Recommended diameters of the pot
bottom (see ''Technical Data Sheet''
supplied with the product).
Try not to spill sugar or pro-
ducts containing sugar on the glass
as while the surface is hot these
EN
MAXIMUN
OPERATING TIME
(in hours)
0
8
8
5
4
4
3
2
2
1
10 or 5 minutes,
readjusts to level 9
(depending on model)
21
Publicidad
Tabla de contenido
