Fitting Instructions - Rola 59967 Instrucciones De Instalación

2011-on, jeep grand cherokee con largueros en el techo, kit de travesaños
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Step 4:
While Taking care to ensure that the strap stays oriented in the roof rail correctly as shown in step 3 above.
Use the L-Wrench Security Key to tighten the Bolt to approximately 5Nm ( 44 in/lbs) of torque or a firm hand-tightness. Fig. 4a.
Repeat Steps 2 though 4 for the opposite side end support and then then the remaining Crossbar assembly assuring proper fit and
alignment.Replace the supplied torx L-wrench to its stowed position in the end support. Fig 4b
Note: The FRONT and REAR Crossbars are NOT the
same length. The FRONT Crossbar is longer. The
Crossbar labeled "FRONT" on the underside of the
Crossbar, belongs to the front location. The remaining
bar, without the label, belongs to the rear location. It is
recommended the spacing between the front and rear
bar is 700mm. Some accessories my require a different
spacing.
Step 5: Attaching Covers to End Supports
Should you need to remove your GTX covers the following describes the
replacement and use.
Locate the ends of the Hinge with the Cover hinge holes. Flex the Hinge ends
in and push through the Cover holes until the capped ends engage. (you'll hear
and audible click) (Fig 6, 7)
To fully extend the Covers away from the Support (to access the
Accessory Channel or mounting hardware) pivot the Cover on the Hinge
while pushing down on the top of the Cover. (Fig 10, 11)
Step 6: Closing the End Support Covers
Close the End Support Covers by moving the cover up, over, and then down
on the End Support. Push Cover against the End Support until you hear an
audible "click", indicating the Cover is fully engaged with the End Support. (fig
13, 14) . Lock all four covers into place using the keys provided. (Fig 12)
Store your keys in a safe place such as the glove box or key ring. Replacement
locks and keys are available as service items.
Step 7: Mounting Accessories
You are now ready to mount your accessories examples: Bike, Kayak, luggage
carriers by using the Accessory Channel if applicable (fig 11). "T" bolts are
available to mount accessories. Be sure to cut your buffer strips to size to
completely cover your channel once the accessories are mounted.
Replacement Buffer Strips are available as service items.
General Usage Information
* It is essential for the proper assembly, operation and use of the Roof Rack
that the instructions and safety precautions supplied are strictly observed.
* The maximum permissible load for your roof rack is the lower of the
maximum load capacity specified in your vehicle owner's manual or specified
on your roof rack load label. Do NOT exceed the maximum load capacity.
Maximum load capacity equals the weight of the rack + accessories + weight
of cargo.
Ensure your vehicle's function is not impaired before driving.
REGULARLY CHECK THE TIGHTNESS OF CROSSBAR ATTACHMENTS.
Loads should be evenly distributed and secured
Check the function of all doors and sunroof before driving.
Any weight carried on the vehicle will adversely affect its handling particularly in cornering or in a cross wind and the vehicle
should therefore be driven with increased caution.
For lost key replacement or other service items call customer service: 1-800-632-3290 or visit:
Please have lock core number or part numbers available.
Only use NON-STRETCH tie down straps.
A number of accessories for carrying special loads are available.
59967N Rev: B 10/13/2015

Fitting Instructions

2011-ON Jeep Grand Cherokee
(with factory roof rails)
Crossbar Kit
L-Wrench
.
Printed in China
PART No:
CARRYING CAPACITY:
Fig 4b
End Support
Cover
End Support
Fig 6
Fig 8
Fig 11
Ensure bars are parallel and straps are tightened against
the side rails. Perform a check by tugging on the Crossbars.
www.rolaproducts.com.
59967
75Kgs/
165 Lbs
Fig 4a
CLICK
Fig 7
Accessory
Channel
Access
Fig 9
Fig 10
CLICK
Fig 12
Pg 2 of 2

Publicidad

Tabla de contenido
loading

Tabla de contenido