Publicidad
Idiomas disponibles
Idiomas disponibles
Installation Instructions – Galleon LED
Installation Instructions
Tools Required
Ratchet, a shallow 3/4" socket and #2 Phillips head
screwdriver.
Pole Mount (FIG. 1)
1.
Loosen (3) screws located in the access door of the
fixture and open the door.
2.
Install the 1st threaded rod through the top side
hole at the back of the fixture. Slide a lock washer
and nut onto the rod inside the housing but do
not tighten. No more than 1/2" of bolt should pass
through the nut inside the housing in order to be
able to tighten the nut during step 8.
3.
Install the 2nd threaded rod through the bottom
side hole at the back of the fixture. Slide a lock
washer and nut onto the rod inside the housing but
do not tighten. No more than 1/2" of bolt should
pass through the housing in order to be able to
tighten the nut during step 8.
4.
Remove the pole top cap.
5.
Insert the threaded rods from steps 2 and 3 through
the upper and lower holes of the arm. Make sure
the angled edge of the arm matches the angle at the
back of the fixture so that the assembly will be level
upon completion. The long side of the arm should
be at the top of the fixture.
6.
Route the fixture leads through the center opening
of the arm and through the center opening of the
pole.
7.
Hold the nut plate on the inside of the pole and
insert the mounting bolts through the pole and
thread into the nut plate. Assure that the bolt is
completely threaded through the nut plate.
8.
Tighten both nuts within the fixture to 40 ft-lbs./
54 N·m. A shallow 3/4" socket must be used in order
to guarantee clearance of all drivers inside the
fixture during this step.
9.
Attach the supply side ground wire to the ground
terminal connector (green wires).
10. Connect the supply side line voltage wire to the
fixture side line voltage terminal connector (black
wires).
11. Connect the supply side neutral wire to the fixture
side neutral wire terminal connector (white wires).
12. Close the cover and tighten the three screws to
insure the fixture will maintain it's water tight seal.
13. Replace pole top cap after completion of fixture
installation and wiring.
2
EATON
IB500011EN
Installation instructions
Notee: For installation to round poles follow the same
instructions as the square pole installation with
the additional round pole adaptor inserted
between the pole and the arm (FIG. 1).
Grommet (For Service Leads)
Threaded Rod
Angled Edge
Arm
Nut Plate
Access Door
Round Pole Adapter (Optional)
Fig 1.
Tools Required
#2 Phillips screw driver, ratchet and a 3/4˝ shallow socket.
Wall Mount (FIG. 2)
1.
Loosen (3) screws located in the access door of the
fixture and open the door.
2.
Install the 1st mounting bolt through the top side
hole at the back of the fixture. Slide a lock washer
and nut onto the bolt inside the housing but do not
tighten.
3.
Install the 2nd mounting bolt through the bottom
side hole at the back of the fixture. Slide a lock
washer and nut onto the bolt inside the housing
but do not tighten.
4.
Slide the included arm over the bolts as shown in
FIG. 2. Make sure the angled portion of the arm
matches the angle at the back of the fixture so that
the assembly will be level upon completion.
The long side should be at the top of the fixture.
5.
Place the decorative wall plate over the arm bolts
and secure to the back side of the arm using the
supplied lockwasher and nuts.
6.
Tighten the nuts on the back of the decorative wall
plate to 40 ft-lbs./54 N·m. Set the fixture assembly
aside.
Mounting Hardware Detail
Publicidad
