Installation Instructions - Eaton Cooper Lighting Galleon IMI-811 Instrucciones De Instalación

Galleon LED Area/Site Luminaire Installation Instructions
TM
SAFETY
This fixture must be wired in accordance with the
National Electrical Code and applicable local codes
and ordinances. Proper grounding is required to insure
personal safety. Carefully observe grounding procedure
under installation section.
WARNING
Make certain power is OFF before starting installation
or attempting any maintenance. Risk of fire/electric
shock. If not qualified, consult an electrician.
• RISK OF ELECTRIC SHOCK—Disconnect power at fuse
or circuit breaker before installing or servicing.
• RISK OF BURN—Disconnect power and allow fixture
to cool before servicing.
• RISK OF PERSONAL INJURY—Fixture may become
damaged and/or unstable if not installed properly.
Tighten all fixture components to their recommended
torque values. Do not lift pole into place by securing
lifting device to lighting fixture or mounting arm.

Installation Instructions

Note: This lighting fixture is designed for outdoor
lighting services, and should not be used in area
of limited ventilation or inside high ambient
temperature enclosures. It must be stored in a
dry location prior to installation. Do not expose
lighting fixture to rain, dust or other
environmental conditions prior to installation
and insertion of photocontrol or shorting cap
(if so equipped). Do not install the fixture near
combustible materials or locate next to airflow
blocking surfaces within 6 inches. Best results will
be obtained if installed and maintained according
to the following recommendations.
Installation
This lighting fixture has been shipped complete with
one of several mounting options. Please follow the
installation instructions specific to the catalog part
that you ordered.
Note: Care must be taken not to set lighting fixture down
on optical lenses or lift the fixture in the lens area.
Tools Required
Ratchet, a shallow 3/4" socket and #2 Phillips head
screwdriver.
Pole Mount (FIG. 1)
1. Loosen (3) screws located in the access door of the
fixture and open the door.
2 LED Area/Site Luminaire Installation Instructions IMI-811 ADH140439 www.eaton.com
Galleon
TM
IMPORTANT
Read before installing fixture. Retain for future
reference.
These instructions do not claim to cover all details or
variations in the equipment, procedure, or process
described, nor to provide directions for meeting every
possible contingency during installation, operation or
maintenance. When additional information is desired
to satisfy a problem not covered sufficiently for user's
purpose, please contact your nearest representative.
NOTE: Specifications and dimensions subject to change
without notice.
WARRANTY/LIABILITY
Consult www.cooperlighting.com for current Limited
Warranty and Limitations of Liability information.
2. Install the 1st threaded rod through the top side
hole at the back of the fixture. Slide a lock washer
and nut onto the rod inside the housing but do
not tighten. No more than 1/2" of bolt should pass
through the nut inside the housing in order to be
able to tighten the nut during step 8.
3. Install the 2nd threaded rod through the bottom side
hole at the back of the fixture. Slide a lock washer
and nut onto the rod inside the housing but do
not tighten. No more than 1/2" of bolt should pass
through the housing in order to be able to tighten
the nut during step 8.
4. Remove the pole top cap.
5. Insert the threaded rods from steps 2 and 3 through
the upper and lower holes of the arm. Make sure
the angled edge of the arm matches the angle at the
back of the fixture so that the assembly will be level
upon completion. The long side of the arm should
be at the top of the fixture.
6. Route the fixture leads through the center opening
of the arm and through the center opening of the
pole.
7. Hold the nut plate on the inside of the pole and
insert the mounting bolts through the pole and
thread into the nut plate. Assure that the bolt is
completely threaded through the nut plate.
8. Tighten both nuts within the fixture to 40 ft-lbs.
A shallow 3/4" socket must be used in order to
guarantee clearance of all drivers inside the fixture
during this step.
9. Attach the supply side ground wire to the ground
terminal connector (green wires).
NOTE