Ryobi ETMS-1426 Manual De Utilización página 16

GB
F D
SAFETY INSTRUCTIONS
Do not leave the saw in the rain and never use it in
■
damp or wet conditions.
Provide good lighting.
■
Never saw near combustible liquids or gases.
■
Wear suitable work clothes! Loose garments or
■
jewellery may become caught up in the rotating
saw blade.
Operators have to be at least 18 years of age.
■
Trainees of at least 16 years of age are allowed to
use the machine only under supervision.
Keep children away from the machine when it is
■
connected to the power supply.
Check the power cable. Never use a faulty or
■
damaged power cable.
Keep your workplace clean of wood scrap and any
■
unnecessary objects.
Persons working on the machine should not
■
be distracted.
Note the direction of rotation of the motor and
■
saw blade.
After you have switched off the motor, never slow
■
down the saw blade by applying pressure to its side.
Fit only blades which are well sharpened and have no
■
cracks or deformations.
The machine is to be operated only with tools which
■
conform with EN 847-1: 1996.
Faulty saw blades have to be replaced immediately.
■
Never use saw blades which do not comply with the
■
data specified in this manual.
Make sure that the arrow on the saw blade complies
■
with the arrow marked on the machine.
Make certain that the saw blade does not touch the
■
turn-table in any setting. To do so, pull out the power
plug and tilt the saw blade by hand into the
45° position and the 90° position. If necessary,
re-adjust the saw head.
It is imperative to make sure that all the devices used
■
to cover the saw blade are in good working order.
Never wedge the hinged guard hood in open position.
■
Never dismantle the machine's safety devices or put
■
them out of operation.
Damaged or faulty safety devices have to be replaced
■
immediately.
Never cut workpieces which are too small to hold
■
securely in your hand.
Do not place your hands in awkward positions where
■
one or both may slip suddenly and touch the saw blade.
E I P NL S DK N FIN
English
When working with long workpieces, use an
■
additional support (table, stand, etc.) to prevent the
machine from tipping over.
Always clamp round workpieces such as dowel
■
rods etc. with suitable devices.
There must be no nails or other foreign bodies in that
■
part of the workpiece you want to cut.
Always stand to the side of the saw blade when
■
working with the saw.
Never load the machine so much that it cuts out.
■
Always press the workpiece firmly against the table
■
and the stop rail to prevent it from wobbling or twisting.
Make sure that off-cuts can be removed from the
■
side of the saw blade. If not, they may catch on the
saw blade crown and be catapulted into the
surrounding area.
Never saw several workpieces simultaneously.
■
Never remove loose splinters, chips or jammed
■
pieces of wood when the saw blade is running.
To rectify faults or remove jammed pieces of wood,
■
always switch off the machine first. Pull out the
power plug!
Conversions, adjustments, measurements and
■
cleaning jobs are to be performed only when the
motor is switched off. Pull out the power plug!
Before you switch on the machine, check that all
■
wrenches and adjustment tools have been removed.
When you leave your workplace, switch off the motor
■
and pull out the power plug.
Electric installation work, repairs and maintenance
■
are to be carried out only by specialists.
All guards and safety devices have to be refitted
■
immediately after completion of any repairs or
maintenance.
It is imperative to observe the manufacturer's safety,
■
operating and maintenance instructions as well as the
dimensions quoted in the technical data.
It is imperative to observe the accident prevention
■
regulations in force in your area as well as all other
generally recognized rules of safety.
Note the information published by your professional
■
associations.
Switch on the dust extraction system each time you
■
use the machine.
The machine may be used in closed rooms only in
■
conjunction with a suitable vacuum extraction system.
The saw must be connected to a 230 V socket.
■
Never use light-duty machines for heavy-duty work.
■
10
GR H CZ RUS RO PL