Technical Characteristics; Optional Accessories - Elkron IM915AM Manual Del Usuario

1.0 TECHNICAL CHARACTERISTICS

- Rated supply voltage ........................... 12V—
- Operating voltage ................................ from 9 to 15V—
- Absorption at 12V— AM version ....... 25 mA rated - max 44 mA (leds ON)
- Absorption at 12V— LX version ........ 20 mA rated - max 39 mA (leds ON)
- Absorption during alarm ...................... max 38 mA (AM version)
- Operation ............................................. AND - OR (programmable)
- Max allowed ripple .............................. 5V Peak-to-peak
- MW Sensitivity reg. with trimmer from 4 to 15 m ± 25%
- IR Sensitivity ........................................ reg. at 2 levels (9 m / 15 m)
- Pulse count .......................................... x 1 x 2 (programmable)
- Max current supplied at fault outputs
- Infrared Sensor ........................................... PIR QUAD
- IR rating ................................................ 15 m (volumetric lens), 15 m
- IR coverage .......................................... 3 selectable fields of coverage
- MW coverage ....................................... 90° horizontal - 36°vertical
- MW output ............................................ 15 m adjustable
- Frequency ............................................ 9.9 GHz / 10.525 Ghz / 10.687 GHz
- The emission frequency is indicated on the label at rear of sensor.
- Sensitive zones 20 at 3 levels (volumetric lens) + 2 creep - zones
1 at 1 level (curtain lens) + 1 creep - zones
7 at 5 levels (long range lens) + 1 creep - zones
- Alarm relay NC 0.1A - 24V— with 4R7 series safety Resistance
- Anti tamper ........................................... 50mA - 24V—
- Operating temperature.......................... from -10°C to + 55°C
- Degree of protection of cover IP 30 IK02
- Size (h x l x d) ..................................... 138 x 74 x 53
- Weight .................................................. 162 gr.

OPTIONAL ACCESSORIES

- Joint - SP5900111 (package of 10 pcs)
- Antiremoval micro for joint KT5000111 (package of 10 pcs)
1.0 TECHNICAL CHARACTERISTICS
- Rated supply voltage ........................... 12V—
- Operating voltage ................................ from 9 to 15V—
- Absorption at 12V— AM version ....... 25 mA rated - max 44 mA (leds ON)
- Absorption at 12V— LX version ........ 20 mA rated - max 39 mA (leds ON)
- Absorption during alarm ...................... max 38 mA (AM version)
- Operation ............................................. AND - OR (programmable)
- Max allowed ripple .............................. 5V Peak-to-peak
- MW Sensitivity reg. with trimmer from 4 to 15 m ± 25%
- IR Sensitivity ........................................ reg. at 2 levels (9 m / 15 m)
- Pulse count .......................................... x 1 x 2 (programmable)
- Max current supplied at fault outputs
- Infrared Sensor ........................................... PIR QUAD
- IR rating ................................................ 15 m (volumetric lens), 15 m
- IR coverage .......................................... 3 selectable fields of coverage
- MW coverage ....................................... 90° horizontal - 36°vertical
- MW output ............................................ 15 m adjustable
- Frequency ............................................ 9.9 GHz / 10.525 Ghz / 10.687 GHz
- The emission frequency is indicated on the label at rear of sensor.
- Sensitive zones 20 at 3 levels (volumetric lens) + 2 creep - zones
1 at 1 level (curtain lens) + 1 creep - zones
7 at 5 levels (long range lens) + 1 creep - zones
- Alarm relay NC 0.1A - 24V— with 4R7 series safety Resistance
- Anti tamper ........................................... 50mA - 24V—
- Operating temperature.......................... from -10°C to + 55°C
- Degree of protection of cover IP 30 IK02
- Size (h x l x d) ..................................... 138 x 74 x 53
- Weight .................................................. 162 gr.
OPTIONAL ACCESSORIES
- Joint - SP5900111 (package of 10 pcs)
- Antiremoval micro for joint KT5000111 (package of 10 pcs)
max 33 mA (LX version)
(curtain lens), 25 m (long range
lens)
max 33 mA (LX version)
(curtain lens), 25 m (long range
lens)
2.0 PRECAUTIONS
- Install the sensor on a hard surface, not subject to vibrations, at a height
of between 2 and 2.2 mt, using the typical detection diagrams as
reference, so that the infrared detects movements occuring within the
protected zone, and the microwave module detects those approaching
the sensor. Avoid placing the sensor close to sources of heat or in direct
sunlight.
- Do not let the MW zone's electromagnetic energy be reflected on wide
surfaces such as mirrors, metal walls, etc.
- Avoid pointing the sensor toward fluorescent lamps and placing it close
to these (the Environmental Test function, described below, could be
helpful for this purpose).
- Avoid the presence of blind zones created by furniture, shelves, etc. in
which the burglar could move, inside the protected area.
- Keep animals out of the protected area.
- For connections, it is advisable to use shielded wire, preferably one wire
for each sensor.
- Keep the system's power supply cables as far as possible from the mains
cable. Adjust microwave sensitivity so that the detection lobe is within
the area to be protected. Do not touch the pyroelectric's specular surface
with one's fingers. Do not install the sensor outside and do not allow
dust to settle on its surface.
- The antimasking protection is set in factory on each detector; so it is very
important not to change the covers when are used more detectors at the
same time
- If the sensor is installed at a height greater than 2.2 meters, you are
recommended to use the optional joint; slant the sensor so as to
best adapt the fields of coverage as needed.
In case of using interface modules (mod. Elkron UR1Z) they must be
installed obligatorily in the outside of the detector wrap.
NOTE: the UR1Z module can be lodged inside the optionalSP900 ball
joint bracket
12
2.0 PRECAUTIONS
- Install the sensor on a hard surface, not subject to vibrations, at a height
of between 2 and 2.2 mt, using the typical detection diagrams as
reference, so that the infrared detects movements occuring within the
protected zone, and the microwave module detects those approaching
the sensor. Avoid placing the sensor close to sources of heat or in direct
sunlight.
- Do not let the MW zone's electromagnetic energy be reflected on wide
surfaces such as mirrors, metal walls, etc.
- Avoid pointing the sensor toward fluorescent lamps and placing it close
to these (the Environmental Test function, described below, could be
helpful for this purpose).
- Avoid the presence of blind zones created by furniture, shelves, etc. in
which the burglar could move, inside the protected area.
- Keep animals out of the protected area.
- For connections, it is advisable to use shielded wire, preferably one wire
for each sensor.
- Keep the system's power supply cables as far as possible from the mains
cable. Adjust microwave sensitivity so that the detection lobe is within
the area to be protected. Do not touch the pyroelectric's specular surface
with one's fingers. Do not install the sensor outside and do not allow
dust to settle on its surface.
- The antimasking protection is set in factory on each detector; so it is very
important not to change the covers when are used more detectors at the
same time
- If the sensor is installed at a height greater than 2.2 meters, you are
recommended to use the optional joint; slant the sensor so as to
best adapt the fields of coverage as needed.
In case of using interface modules (mod. Elkron UR1Z) they must be
installed obligatorily in the outside of the detector wrap.
NOTE: the UR1Z module can be lodged inside the optionalSP900 ball
joint bracket
12