Packing List; Volt Lithium-Ion Cordless Line Trimmer - Ego Power+ ST1300E Manual Del Propietário

Ocultar thumbs Ver también para ST1300E:
Tabla de contenido

Publicidad

Cutting Width
Recommended Operating Temperature 0°C-40°C
Recommended Storage Temperature -20°C-70°C
Weight (without battery pack)
Measured sound power level L
Max. sound pressure level at
operator's ear L
PA
Guaranteed sound power level L
(according to 2000/14/EC)
Front handle
Valuation of
vibration a
h
Rear handle
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
The declared vibration total value may also be used in
a preliminary assessment of exposure.
NOTICE:
The vibration emission during actual use of the
power tool can differ from the declared value in which the
tool is used;In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.

PACKING LIST

PART NAME
Line Trimmer
Guard
Front-assist Handle Assembly
Hex Wrench
Operator's Manual
DESCRIPTION
KNOW YOUR LINE TRIMMER (Fig. A)
1. Trigger
2. Rear Handle
3. Lock-off Lever
4. Speed Adjustment Switch
5. Soft Sleeve
6. Adjustable Front-assist Handle
7. Trimmer Head (Bump Head)
8. Bump Knob
9. Line-cutting Blade
10. Guard
11. Ejection Mechanism
33 cm
12. Electric Contacts
13. Latch
14. Battery-release Button
2.76 kg
ASSEMBLY
89.25 dB(A)
K=2.5 dB(A)
WA
75.2 dB(A)
do not operate this product until the parts are replaced.
K=2.5 dB(A)
Use of this product with damaged or missing parts could
93 dB(A)
result in serious personal injury.
WA
2.134 m/s
2
create accessories not recommended for use with this line
K=1.5 m/s
2
trimmer. Any such alteration or modification is misuse and
1.231 m/s
2
could result in a hazardous condition leading to possible
K=1.5 m/s
2
serious personal injury.
cause serious personal injury, always remove the battery
pack from the tool when assembling parts.
MOUNTING THE GUARD
replacing the guard. Take care of the blade on the guard
and protect your hand from cutting.
guard firmly in place. The guard must always be on the
tool to protect the user! When the guard was fixed,
QUANTITY
never attempted to remove or adjust the guard, if
replace needed, it shall be performed by a qualified
1
service technician!
1
Loosen and remove the two combination screws from the
1
shaft base (Fig. B). Align the guard mounting holes with
the assembly holes and then lock the guard onto the shaft
1
base with the two screws. Make sure the guard is fixed
1
according to Fig. B & C, any reverse fixing will cause
great danger!
MOUNTING AND ADJUSTING THE FRONT-ASSIST
HANDLE
Push the front-assist handle onto the shaft (Fig. E), then
insert the clamping block into the handle slot (Fig. F),
mount the lock pole, lock them with the wing nut (Fig.
G). The sequence is as Fig. D shown. Lastly, adjust the
front-assist handle position to make sure your front arm
is straight when using the trimmer (Fig. H) and then lock
the lever of the lock pole (Fig. I).
Fig. D & H parts description see below:
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1300E
WARNING:
If any parts are damaged or missing,
WARNING:
Do not attempt to modify this product or
WARNING:
To prevent accidental starting that could
WARNING:
Always wear gloves when mounting or
WARNING:
Never operate the tool without the
D-1 Front-assist Handle
D-2 Lock Pole
EN
D-4 Wing Nut
H-1 Soft Sleeve
9

Publicidad

Tabla de contenido
loading

Tabla de contenido