Packing List - Ego Power+ ST1300E Manual De Operación

◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating
condition. Be aware of possible hazards even when
EN
the tool is not operating. Take care when performing
maintenance or service.
◾
Do not wash with a hose; avoid getting water in motor
and electrical connections.
◾
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan this tool to someone else, also loan these
instructions to them to prevent misuse of the product
and possible injury.
◾
Always wear substantial footwear and long trousers
while operating the machine.
◾
Always be sure of the footing on slopes and to walk,
never run.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Voltage
56 V
No-load Speed 5200-6500 /min
Cutting Mechanism Bump Head
Cutting Line Type AL0801 2.0mm
Nylon twist line
Cutting Width 33 cm
Weight TBD
(without battery pack)
Measured sound power level L TBD
WA
Sound pressure level at operator's TBD
ear L
PA
Guaranteed sound power level L TBD
WA
(according to 2000/14/EC)
Valuation Front-assist Handle TBD
of vibra-
Rear Handle TBD
tion:
◾
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾
The declared vibration total value may also be used in a
preliminary assessment of exposure.
NOTICE:
The vibration emission during actual use of the
power tool can differ from the declared value in which the
tool is used;In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.
8
56 VOLT LITHIUM-ION CORDLESS STRING TRIMMER — ST1300E
All manuals and user guides at all-guides.com

PACKING LIST

QUANTITY
PART NAME
1
String Trimmer
1
Guard
1
Front-assist Handle Assembly
1
M5 Hex Wrench
1
Operator's Manual
DESCRIPTION
KNOW YOUR STRING TRIMMER (Fig. A)
1. Trigger
2. Rear Handle
3. Lock-off Lever
4. Speed Adjustment Switch
5. Soft Sleeve
6. Adjustable Front-assist Handle
7. Trimmer Head (Bump Head)
8. Bump Knob
9. Line-cutting Blade
10. Guard
11. Ejection Mechanism
12. Electric Contacts
13. Latch
14. Battery-release Button
ASSEMBLY
WARNING:
If any parts are damaged or missing, do
not operate this product until the parts are replaced. Use of
this product with damaged or missing parts could result in
serious personal injury.
WARNING:
Do not attempt to modify this product or
create accessories not recommended for use with this string
trimmer. Any such alteration or modification is misuse and
could result in a hazardous condition leading to possible
serious personal injury.
WARNING:
To prevent accidental starting that could
cause serious personal injury, always remove the battery
pack from the tool when assembling parts.
MOUNTING THE GUARD
WARNING:
Always wear gloves when mounting or
replacing the guard. Take care of the blade on the guard
and protect your hand from cutting.
WARNING: Never operate the tool without the guard
firmly in place. The guard must always be on the tool
to protect the user! When the guard was fixed, never
attempted to remove or adjust the guard, if replace
needed, it shall be performed by a qualified service
technician!
Loosen and remove the two combination screws from the
shaft base (Fig. B). Align the guard mounting holes with the
assembly holes and then lock the guard onto the shaft base
with the two screws. Make sure the guard is fixed according
to Fig. B & C, any reverse fixing will cause great danger!
MOUNTING AND ADJUSTING THE FRONT-ASSIST HANDLE
Push the front-assist handle onto the shaft (Fig. E), then
insert the clamping block into the handle slot (Fig. F), mount
the lock pole, lock them with the wing nut (Fig. G). The
sequence is as Fig. D shown. Lastly, adjust the front-assist
handle position to make sure your front arm is straight
when using the trimmer (Fig. H) and then lock the lever of
the lock pole (Fig. I).
Fig. D & H parts description see below:
D-1 Front-assist Handle D-4 Wing Nut
D-2 Lock Pole H-1 Soft Sleeve
D-3 Clamping Block H-2 Warning Label
NOTICE:
The front-assist handle should be turned
upwards to point toward the top of the handle.
WARNING:
Only fix the front-assist handle in front of
the soft sleeve on the shaft.
WARNING:
The tool can not be used without the front-
assist handle reliably fixed.
OPERATION
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side
shields. along with hearing protection. Failure to do so
could result in objects being thrown into your eyes and
other possible serious injuries.
WARNING:
Do not use any attachments or
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
56 VOLT LITHIUM-ION CORDLESS STRING TRIMMER — ST1300E
WARNING:
Use your string trimmer equipped with
the appropriate cutting line only for cutting grass and
similar material.
You may use this product for the purposes listed below:
Trimming: used for removing grass and weeds up against
walls, fences, trees and borders.
Cutting: used for cutting the grass that is difficult to reach
using a normal mower.
NOTICE:
The tool is to be used only for its prescribed
purpose. Any other use, for example edge trimming, is
deemed to be a case of misuse.
ATTACHING/DETACHING THE BATTERY PACK
Fully charge before first use.
To Attach
Align the battery ribs with the mounting slots and press the
battery pack down until you hear a "click" (Fig. J).
To Detach
Depress the battery-release button and pull the battery
pack out as Fig. K shown.
HOLDING THE STRING TRIMMER
WARNING:
Dress properly to reduce the risk of injury
when operating this tool. Do not wear loose clothing or
jewelry. Wear eye and ear/hearing protection. Wear heavy
duty, long trousers, boots and gloves. Do not wear short
trousers, sandals or go barefoot.
Before operating, hold the trimmer with both hands, one
hand on the rear handle and the other on the front-assist
handle which shall be straight (Fig. L). Then check for
balanced footing and a proper cutting distance without
operator bending over.
STARTING/STOPPING THE STRING TRIMMER
To Start
Press down the lock-off lever and hold it in that position.
Depress the trigger to turn on the string trimmer as Fig. M
shown.
To Stop
Release the lock-off lever and the trigger.
NOTICE:
The motor has two speeds for cutting, Position"1"
for lower speed and Position "2" for high speed, as Fig.
M shown. Just push the speed adjustment switch to the
suitable position during cutting.
EN
9