Important Safety Instructions For Battery Chargers - Porter Cable PCC671 Manual De Instrucciones

WARNING:
personal hearing protection that
conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration of
use, noise from this product may contribute
to hearing loss.
WARNING:
glasses. Everyday eyeglasses are NOT
safety glasses. Also use face or dust mask
if cutting operation is dusty. ALWAYS
WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING:
power sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to the state
of California to cause cancer, birth
defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• c rystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING:
generate and/or disperse dust, which may
cause serious and permanent respiratory or
other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate
for the dust exposure. Direct particles away
from face and body.
WARNING:
tool for long periods of time. Vibration
caused by the operating action of this tool
may cause permanent injury to fingers,
hands, and arms. Use gloves to provide
extra cushion, take frequent rest periods,
and limit daily time of use.
• When using an extension cord, be sure to
use one heavy enough to carry the current
your product will draw. An undersized cord
will cause a drop in line voltage resulting
in loss of power and overheating. The
following table shows the correct size
Always wear proper
ALWAYS use safety
Some dust created by
Use of this tool can
Do not operate this
to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the
gage number, the heavier the cord.
Minimum Gauge for Cord Sets
volts
120V 0-25
(0-7,6m)
Ampere Rating
More Not more
Than Than
0 - 6 18
SAvE ThESE INSTRUCTIONS
SYMBOLS
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V ..................volts
A ..................amperes
Hz ................hertz
W .................watts
min ..............minutes
or AC ......alternating current
or DC ...direct current
n o ................no load speed
................Class I Construction
(grounded)
................earthing terminal
................safety alert symbol
................Class II Construction
(double insulated)
.../min or rpm...revolutions or
SPM ............Strokes per minute
.............Read instruction manual before use
...............Use proper eye protection
................Use proper hearing protection
................Use proper respiratory protection
IMPORTANT SAFETY
INSTRUCTIONS FOR
BATTERY ChARGERS
SAvE ThESE INSTRUCTIONS: This
manual contains important safety
instructions for battery chargers.
• Before using charger, read all instructions
and cautionary markings on charger, battery
pack, and product using battery pack.
WARNING:
allow any liquid to get inside charger.
CAUTION:
the risk of injury, charge only designated
Porter Cable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION:
with the charger plugged in to the power
supply, the charger can be shorted by
foreign material. Foreign materials of a
conductive nature such as, but not limited
to, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away
from charger cavities. Always unplug the
4
Total Length of Cord in Feet
26-50 51-100
(7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
American Wire Gauge
16 16 14
reciprocation per minute
Shock hazard. Do not
Burn hazard. To reduce
Under certain conditions,
101-150