Electrical Safety; Assembly And Adjustment - DeWalt DW728KN Traducido De Las Instrucciones Originales

1 pin wrench
3 box spanners (10, 13 & 17 mm)
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Description (fi g. 1)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
a. On/off switch
b. Handle
c. Front guard
d. Lower guard
e. Fixed table top
f. Switch box
g. Leg
h1. Left fence (small)
h2. Right fence (large)
i. Dust shroud
j. Mitre latch lever
k. Mitre clamp lever
l. Height adjustment crank
m. Radial arm
n. End-cap
o. cable
p. Dust outlet
q. Yoke assembly
r. Motor
s1. Left table strip
s2. Right table strip
t1. Left table extension
t2. Right table extension
u. Bevel scale
v. Roller head assembly
w. Isolating switch (DW729KN)
INTENDED USE
The radial arm saw has been designed for professional woodworking.
This high precision machine can be easily and quickly set to crosscut,
bevel, mitre. For optimum safety, all major controls have both a latch
and a locking device. Also refer to the quick reference chart at the end
of the section. This saw is designed for use with a 350 mm diameter
carbide tip blade.
DO NOT use under wet conditions or in presence of flammable liquids
or gases.
The radial arm saw is a professional power tool.
DO NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.

Electrical Safety

The electric motor has been designed for one voltage only. Always
check that the power supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by a specially
prepared cord available through the D
Mains Plug Replacement
(U.K. & Ireland Only)
SINGLE-PHASE ONLY
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
WALT service organization.
E
• Connect the brown lead to the live (L) terminal in the new plug.
• Connect the blue lead to the neutral (N) terminal.
• Connect the green/yellow lead to the earth (E) terminal.
WARNING: Follow the fitting instructions supplied with
good quality plugs. Recommended fuse: 13 A.
WARNING: This product must be earthed. Always check
that the power supply corresponds to the voltage on the
rating plate.
Contact a qualified electrician if a new CEE 16 A industrial plug needs
to be fitted.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary.
Use an approved extension cable suitable for the power input of your
machine (see technical data). When using a cable reel, always unwind
the cable completely. The maximum cable length is 30 m.
SINGLE-PHASE MACHINES
Use an approved 3-core extension cable suitable for the power input
of this machine (see technical data). The minimum conductor size is
1.5 mm².
THREE-PHASE MACHINES
Please ensure the cable is provided with CEE 16A industrial plug/
coupler according to IEC 60309.
Voltage Drops
Inrush currents cause short-time voltage drops. Under unfavourable
power supply conditions, other equipment may be affected.
If the system impedance of the power supply is lower than 0.25 Ω,
disturbances are unlikely to occur.
Sockets used for these machines shall be fused with 16 Amperes
cut-out with an inert characteristic.

ASSEMBLY AND ADJUSTMENT

WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting or
changing set-ups or when making repairs. Be sure the
switch is in the OFF position. An accidental start-up can
cause injury.
WARNING: For optimum performance of your saw, it is of
vital importance to follow the procedures in the paragraphs
below.
Set Up
MOUNTING THE HEIGHT ADJUSTMENT CRANK (FIG. 1, 2, 3)
1. Rotate the arm to the central position.
2. Press the mitre latch lever (j) down as shown (fig. 2).
3. Tighten the mitre clamp lever (k).
4. Introduce the height adjustment crank (l) into the column (x) as
shown until the crank engages in the nut inside the column.
5. Turn the height adjustment crank clockwise until it is fully seated
(fig. 3).
6. Align the mitre scale (yy) with the pointer (xx) and tighten the three
screws (bb) inside the height adjustment crank with 6 mm hex
wrench.
7. Raise the height adjustment crank high enough to provide
clearance for removal of various elements under the motor.
ASSEMBLING THE LEGSTAND (FIG. 1, 4)
The legstand components and fasteners are packed separately.
1. Remove all parts from the package.
2. Lock the arm using the mitre clamp lever (k).
3. Tilt the machine carefully from the pallet until the rear of the column
is resting on the floor.
4. Place a piece of wood (y) under the edge of the table (fig. 4).
5. Assemble the legs (g) as shown using the nuts, bolts and flat
washers provided.
ENGL ISH
31