Hi/Low Power Selection (Only In Pmr446 Band); Vibra-Call Function; Call Feature; Roger Beep (End Transmission Tone) - Midland G8 Manual De Instrucciones

› Push the MENU button again till the display shows DCS and the tone code blinks on the right ("of"=no code
– default condition).
› Select the desired DCS code by pushing ▲▼.
› To confirm the setting, press the PTT or wait for 5 seconds.
! Channel P8 with DCS tone 50 (P850) has been set at factory for the "Emergency" function; do not use
it for general communications!!
Deactivating the DCS codes:
› Select the desired channel.
› Press the MENU key till the display shows the channel in use and the DCS code blinks on the right.
› Select "of" by pushing ▲▼.

Hi/low power selection (only in PMR446 band)

To select the power level, press the MENU button till the display shows Pr. Use ▲▼ to select L (low power) or H
(high power). To confirm your selection, push PTT or wait for 5 seconds.
When the batteries are fully charged, the high power is 500 mW (ERP), while the low is 10mW (ERP).
If your radio has to operate within a short range, you can select the low power and therefore extend the battery
life.
VOX function
Midland G8 enables hands free conversations through the VOX function: just speak in the direction of the
microphone and the communication will be automatically activated.
3
The VOX sensitivity can be adjusted in 3 different levels. You can enable the VOX function with or without
2
5
accessories.
The fourth level activated is the Vox TalkBack: if one radio is continuously transmitting in VOX, the VOX TB will
1
automatically stop the transmission after 20 seconds to allow the transmission to the other users as well.
To activate the VOX function press the MENU button till VOX appears on the display.
Use ▲▼ to select the sensitivity levels:
› Of: Off;
› 1: High
› 2: Middle
› 3: Low
› 4: Talk Back (with high sensitivity)
To confirm your selection, press PTT or wait for 5 seconds.
To disable the VOX function, follow the procedure here above indicated and select oF.

Vibra-CALL function

Midland G8 is equipped with the "Vibra-CALL" feature, which provides a silent alert for incoming CALLs.
To activate this feature, press the MENU button until the display shows
enable this feature (on: enables, oF:disables);
Push PTT [11] to confirm or wait for 5 seconds.

CALL feature

Midland G8 can send 5 different CALL tones. To send this audio signal to other users, press the CALL/
To select the CALL tones:
Press MENU, until the display shows "CA" and the active tone code.
19
By pushing ▲▼ you will hear the 5 pre-set melodies.
Confirm by pressing PTT or wait for 5 seconds.

ROGER BEEP (End transmission tone)

When the PTT button is released, the radio will beep to confirm to other users that your transmission has 18
finished.
In the Midland G8 this function is factory disabled.
17
To activate it:
Press the MENU button until the display shows "rb of"; using the scroll buttons ▼▲ select "on" and "rb on" will
16
be displayed; to confirm the roger beep activation, press PTT or wait for 5 seconds.
4 6 8 7
11
9
10
12
13
14
3
2
5
1
20
EMG OUT
DW
H L
DCS CTC
21
ROGER
22
19
EMG
CALL
23
24
MENU
25
15
18
17
16
4 6 8 7
11
9
10
12
13
14
; use the ▼▲ buttons to disable or
20
EMG OUT
DW
H L
DCS CTC
21
ROGER
22
EMG
CALL
23
24
MENU
25
15
key.
17