Technical Specifications - GYMFORM ABS-A-Round PRO PLATINUM Manual De Instrucciones

Ocultar thumbs

Contenido

página de 33

/ 33
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

pulling them from the edge and then replace the protective

plastic backing on the electrodes. This will help extend the

useful life of the electrodes.

Using the Belt

Press the ON/OFF button for one second to switch on your

GYMFORM® ABS-A-ROUND PRO PLATINUM.

Figure A:

1. LCD display

2. Abdominal part

3. Oblique part

4. Lower-back part

5. Programme

Programme Selection

Programme 1

General massage

Programme 2

Fine tuning

Programme 3

Toning

Programme 4

General conditioning

Programme 5

Glutes and Thighs

Programme 6

Lymphatic

drainage,

effect and pressure

Programme 7

Muscle Building

Programme 8

Fat Burning

Programme 9

Firming Massage

You will see that the LCD display (8) defaults to programme 1

(see Figure A). If you wish to select programme 2 or any other

programme, press the programme-selection button (11), which

is marked with the letter P, until the desired programme appears

on the screen. After reaching programme 9, the screen will dis-

play programme 1 again.

Intensity Selection

When you have selected the programme, choose the intensity

level for each part by pressing the button to select the belt part

(12), which is marked with the letters FSB. As you can see in

Figure A, the intensity level for the abdominal part is indicated by

the number above the letter F, for the oblique parts it is indica-

ted above the letter S and for the lower-back part it is indicated

above the letter B. You can choose between the three parts by

pressing the FSB button. When the digits of the chosen part

flash, press the button to increase the intensity level (13) or

the button to decrease the intensity level (14). When you have

selected the intensity level for one part, press the FSB button

(12) to select the next part you wish to adjust the intensity level

for. You can select a different intensity level for each belt part,

since the sensitivity of each body part varies. Each programme

has 99 intensity levels. We recommend that you increase the

intensity level very little until you are familiar with the device.

Once you have chosen your desired intensity level for all three

belt parts, you can enjoy your training session.

GYMFORM® ABS-A-ROUND PRO PLATINUM

Automatic power off

For your safety, the automatic period for each programme is 10

minutes. GYMFORM® ABS-A-ROUND PRO PLATINUM will

automatically switch itself off 10 minutes after being switched

on, regardless of the level or programme selected.

If you wish to finish your session before the end of the program-

me time, press the ON/OFF button for one second until the LCD

display goes off.

Automatic Reset

When you finish the programme, the device will switch itself

off automatically. When you switch it on again, you will have to

programme it again.

Using the Leg and Arm Belt

roller

Attach the GYMFORM® ABS-A-ROUND PRO PLATINUM unit

(1) to the front of the leg and arm belt (5) using the six snap

fasteners. Ensure that they are all well fastened.

Attach the two electrodes (9) to the belt using the snap faste-

ners.

Remove the protective plastic backing from the electrodes

(make sure you replace it after use).

Position the belt on the area you wish to work on (see figure

below) and ensure that the belt is well secured with the quick

opening and closing system so that the electrodes are in con-

tact with the skin.

To choose the programme and intensity level, please follow the

instructions given in the above section "Using the Belt". In order

to adjust the intensity level, choose the belt part marked with the

letter F on the screen.

AREAS WHERE THE LEG AND ARM BELT MAY BE USED

(Fig. 4)

Front part

G) Lower front

J) Outer upper

thigh

thigh (back)

H) Upper front

thigh

I) Thigh

outer upper

thigh (front)

WE RECOMMEND THAT YOU REPLACE THE ELECTRO-

DES AFTER EVERY 30 USES. IF YOU NOTICE THE ELEC-

TRODES HAVE PREMATURELY LOST THEIR ADHESIVE

POWER, WET THEM WITH A DAMP SPONGE.

NOTE: If you feel heat in the areas where you have attached

the electrodes or if the contractions become weak during the

session, it is likely that the batteries need to be replaced. Re-

move them and insert new ones. If this does not solve the

problem, the electrodes have probably reached the end of

their useful life. Switch off GYMFORM® ABS-A-ROUND PRO

PLATINUM, take it off, fit new electrodes to the belt and then

resume your session. For your convenience, GYMFORM®

ABS-A-ROUND PRO PLATINUM will automatically set the

intensity level to 0 if you change the programme.

NOTE: If the unit does not work properly, press the RESET

button (located on the back of the unit) to restart the unit and

resume normal operation. Press the RESET button (16) with

the tip of a pen or pencil.