Technical Specifications; Cleaning And Maintenance - GYMFORM SIX PACK SPORT Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 7

TECHNICAL SPECIFICATIONS:

Shape of initial curve
Biphasic
pulse
Pulse duration
320 μs
Pulse frequency
3.3 ~ 33.3 Hz
Output voltage
36 V+/-5 V Load resistance
1000 ohm
Input voltage
3 V
Duration of session
Automatic power off after 20
minutes
Intensity
Adjustable from 1 to 10
Mode
1 variable frequency mode
Operating conditions:
10°C~40°C
30%~85% RH
Storage conditions:
-10°C~50°C (14°F~122°F);
10%~95% RH
Maximum power con-
32mA
sumption
This symbol indicates that the device is protected
against electrostatic discharge by BF-type double
insulation.
ISO 7000-1641 User Guide

CLEANING AND MAINTENANCE

DO NOT WASH THE Gymform® SIX PACK UNIT: WIPE
WITH A DRY OR DAMP CLOTH.
Remove the batteries from your Gymform ® SIX PACK if
you do not plan to use it for an extended period of time.
MAINTENANCE AND STERILIZATION OF ADHESIVE
PADS
- Sterilize by wiping with wet fingers.
- Do not immerse in water.
- Keep in a cool, dry place at room temperature.
- Do not remove the insulating label.
- After using the device, always replace the protective
plastic backings on the adhesive electrodes.
- Store in the bag supplied.
PRECAUTIONS WITH BATTERIES
Ensure the battery is properly installed before turning the
square
wave
unit on.
Turn the unit off to replace the battery.
Remove the battery if you are not going to use the device for
an extended period of time.
Take the necessary precautions when disposing of the bat-
tery. Do not expose it to fire.
TROUBLESHOOTING
Problem
THE
PI-
LOT LIGHT
DOES NOT
COME ON
(50°F~104°F);
THE PILOT
LIGHT CO-
MES
ON
BUT
THE
UNIT DOES
NOT WORK
Cause
Solution
- The battery has
- Install the bat-
not been installed.
tery.
- The battery has
- Check that the
not been installed
"+" terminal of the
correctly.
battery is facing
- The battery has
upwards.
run out.
- Replace the bat-
tery.
- There is no con-
- Check that the
tact with the skin.
gel pad is in direct
- The console is not
contact with the
properly attached
skin.
to the Gymform®
- Check that the
Six Pack unit.
console is pro-
- The intensity level
perly attached to
is set to 0.
the Gymform® Six
- The microproces-
Pack unit using
sor has crashed.
the snap faste-
- The battery is
ners.
running low.
- Press the "+ /
button to increase
the intensity.
- Restart it by re-
moving the battery
and replacing it
after one minute.
- Replace the bat-
tery.
THE
BUT-
- The microproces-
TONS
DO
sor has crashed.
NOT WORK
- The battery is
PROPERLY
running low.
DISPOSAL OF MATERIALS
A symbol of a crossed-out wheeled bin means you
should find out about and follow local regulations
about disposing of this kind of product.
Do not dispose of this product as you would other
household waste. Dispose of this device in accordance with
the corresponding local regulations.
Electrical and electronic devices contain hazardous subs-
tances that can have harmful effects on the environment
and/or human health and should be recycled properly.
The battery should be disposed of separately. To protect
the environment, all batteries, including rechargeable ones,
should not be disposed of as you would other household
waste. Take them to a disposal centre and ensure it com-
plies with applicable legislation on battery disposal.
Quality Warranty:
This product is covered by a warranty against manufactu-
ring defects subject to the time periods stipulated by the
legislation in force in each country.
This warranty does not cover damages resulting from ina-
dequate use, negligent commercial use, abnormal wear and
tear, accidents or improper handling.
Australia & New Zealand only
"
I
This product has the benefit of certain Consumer Guaran-
tees. These are prescribed by the Australian Consumer Law
& the New Zealand Consumer Guarantees Act 1993 both
of which provide protection for consumers. There is no ex-
press warranty for this product in Australia or New Zealand.
The above paragraph refers to other countries.
Made in China.
- Restart it by re-
moving the battery
and replacing it
after one minute.
- Replace the bat-
tery.

Publicidad

Tabla de contenido
loading

Tabla de contenido