Bixolon SPP-R210 Guia De Instalacion página 20

◈ MSR Usage
◈ SCR Usage
◈ Self-test
Run the self-test when first setting the printer or when encountering a problem, and check the
following.
• Control Circuit, Mechanisms, Print Quality, ROM Version, and Memory Switch Settings
If no issue is found with the printer after running the self-test, examine the other devices or
peripherals and software. This function is independent of such other devices and software.
• Self-Test Instructions
1) Turn the printer power off and close the printer paper cover.
2) Pressing the paper feed button and power button simultaneously turns the printer on.
3) After printing begins, please release the two buttons.
4) To add a printout of the ASCII pattern, press the paper feed button once more.
5) After the ASCII pattern is printed out, the self-test is automatically terminated.
◈ Product Specifications
Item
Printing Method Thermal printing
90 mm/sec (Receipt Paper)
Printing Speed
60 mm/sec (Linerless Paper)
Resolution 203 DPI
Paper Supply Mode Easy paper loading
Character Size Font A: 12 × 24
Characters Per Line Font A: 32
English: 95
Character Set Expanded Graphics: 128 × 33 pages
International: 32
1 Dimension: UPC A, UPC E, CODE 39, CODE 93,
Printing
Barcode
2 Dimension: PDF417, DATAMATRIX, MAXI,
Emulation BXL/POS
Windows XP(32/64bit) / WEPOS /
Driver 2003 Server(32/64bit) / VISTA(32/64bit) /
2008 Server(32/64bit) / 7(32/64bit) / 8(32/64bit)
Windows XP / WEPOS / 2003 Server /
SDK
VISTA / 2008 Server / 7 / 8 / CE 3.0 and later
Sensor Paper End, Paper Cover Open
Cutter Type Tear-Bar
Language User language supported
Paper Form
Paper Type
Diameter
Paper
Width
Thickness
※ Note
1) This equipment is indooruse and all the communication hiring are limited to inside of the
building.
2) The switch is the disconnecting device. Turn off switch from any hazard.
◈ Black Mark Paper Printing Function
1. Black Mark Function Setting
Black mark paper available at the black mark mode.
• Setting Operations
1) Turn on the printer power.
2) Open the paper cover and press and hold down the paper feed button for longer than two
seconds.
3) After the buzzer tone is emitted, insert paper and close the cover.
4) Repeat the steps above to return to receipt mode.
• Setting Via Memory Switch
1) Please refer to the memory switch changing section of the Commands Manual.
2. Auto Calibration Function
The black mark printing function requires the recognition of black mark paper's black bar
in order to print.
1. Insert the card as shown in the
image and swipe in the direction of
the arrow.
(can be done in both directions)
※ Note
If the card does not register, first
check to see if it is properly aligned.
When swiping the card, the
recommended swiping speed is 100 ~
1200 mm/sec.
1. Insert the Smart card as shown in
the image
2. After using, eject the Smart card.
Description
Font B: 9 × 17 Font C: 9 × 24
Font B/C: 42
Code 128, EAN 8, EAN 13, ITF, Codabar
QR Code
Receipt Linerless
Thermal paper Thermal paper
Max. ø30 mm (1.18") Max. ø30 mm (1.18")
57.5 ± 0.5 mm 57.5 ± 0.5 mm
(2.26" ± 0.2") (2.26" ± 0.2")
0.07 ± 0.003 mm 0.08 ± 0.008mm
If black mark paper's black bar are not properly recognized, use the auto calibration
function.
• Auto Calibration Instructions
1) Turn the printer power off while in black mark print mode.
2) Press and hold down the paper feed button and then press the power button.
3) After the following printout is outputted, press the power button to perform auto
calibration.
Auto Calibration: Power Button
Self Test: Feed Button
4) Three pages of label paper are outputted when performing auto calibration.
◈ Peripherals Connection
※ Note
Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection.
You can check the Bluetooth environment (authentication, encryption, connection mode) and
the wireless LAN environment (IP, SSID, authentication, encryption) via the self-test page.
◈ Printer Cleaning
If the interior of the printer is dusty, print quality can decline.
In such a case, follow the instructions below to clean the printer.
• Make sure to turn the printer power off prior to cleaning.
• As the print head gets very hot during printing, if intending to clean the print head, turn the
printer power off and wait approximately 10 minute before commencement.
• When cleaning the print head, take care not to touch the heated portion of the print head.
→ The print head is susceptible to damage from static electricity, etc.
• Take care not to allow the print head to become scratched and/or damaged in any way.
1) Open the paper cover and remove any paper that may be present.
Use the cleaning pen to clean the printer head in a direction from the center to the
outside.
2) Wipe the print head with a cleaning pen.
3) Remove paper dust from the paper detection sensor using the cleaning pen.
4) Do not use the printer for 10 minutes after cleaning the printer head until the cleaning
agent of the cleaning pen has completely evaporated and dried.
5) Insert the paper and then close the printer's cover.
◈ Certification
This marking shown on the product or its literature, indicates that it should not be
disposed of with other household wastes at the end of its working life. To prevent
possible harm to the environment or people from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should contact either the retailer
where they purchased this product, or their local government office, for details of where
and how they can take this item for environmentally safe recycling. Business users should
contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal.
The following Bluetooth mark and QD ID D022644 is only applicable to models with the
Bluetooth SIG qualification.
☎ BIXOLON Co., Ltd.
● Website http://www.bixolon.com
● Korea Headquarters
(Add) 7~8F, (Sampyeong-dong), 20, Pangyoyeok-ro241beon-gil,
Bundang-gu, Seongnam-si, Gyeonggi-do, 13494, Korea (ROK)
(Tel.) +82-31-218-5500
● U.S. Office
(Add) BIXOLON America Inc., 3171 Fujita St, Torrance, CA 90505
(Tel.) +1-858 764 4580
● Europe Office
(Add) BIXOLON Europe GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf
(Tel.) +49 (0)211 68 78 54 0
Select the mode
1. Bluetooth & Wireless LAN Connection
1) The printer can be connected to devices
equipped with Bluetooth communication
capacity (PDAs, PCs, etc.).
2) Use the Bluetooth connection function
supported by the device to connect to the
printer.
3) The printer can be connected to other
stations, such as PDAs and PCs supporting
wireless LAN communication in Ad-hoc
mode and AP in Infrastructure mode.
2. Interface Cable Connection
1) Open the Interface Cap
2) Connect the interface cable (optional) to the
cable connector of the printer.