Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
'4 _,_ ""
• _ • _
_,
_
•__
• _•,
tec the W :; te S ppV
Read all directions
before
you begin.
IMPORTANT:
If you turn on the refrigerator
before the water
line is
connected,
turn off the ice maker
to avoid
excessive
noise or
damage
to the water
valve.
Connect
to Water
Line
1.
Unplug
refrigerator
or disconnect
power.
Z
Slip the compression
sleeve and compression
nut on the copper
tubing
as shown. Insert the end of the tubing
into the outlet end
squarely
as far as it will go. Screw compression
nut onto outlet
end with adjustable
wrench.
Do not overtighten
or you may
crush the copper
tubing.
8.
Place the free end of the tubing
in a container
or sink, and turn
ON the main water supply.
Flush the tubing
until water
is clear.
Turn OFF the shutoff valve
on the water
pipe.
2.
Turn OFF main water
supply. Turn ON
nearest faucet
long
enough
to clear
line of water.
3.
Find a 1/2" to 11/4 '' (12.7 mm to 31.8 mm) vertical
cold water
pipe
near the refrigerator.
IMPORTANT:
Connect
to Refrigerator
Depending
on your model, the water
line may come down from the
top or up from the bottom.
Follow
the connection
instructions
for
your model.
4.
•
Make
sure it is a cold water
pipe.
•
Horizontal
pipe will work, but the following
procedure
must
be followed:
Drill on the top side of the pipe, not the
bottom.
This will help keep water
away
from the drill. This
also keeps normal
sediment
from collecting
in the valve.
Determine
the length of copper
tubing
you need. Measure
from
the connection
on the lower right rear of the refrigerator
to the
water
pipe. Add 7 ft (2.1 m) to allow for cleaning.
Use 1¼,,
(6.35 mm) O.D. (outside diameter)
copper
tubing.
Be sure both
ends of copper
tubing
are cut square.
Style 1
1.
Remove
plastic cap from water
valve inlet port. Attach
the
copper
tube to the valve
inlet using a compression
nut and
sleeve as shown. Tighten
the compression
nut. Do not
overtighten.
Confirm
copper
tubing
is secure by pulling
on
copper
tubing.
2.
Create
a service
loop with the copper
tubing.
Avoid
kinks when
coiling
the copper
tubing.
Secure copper
tubing
to refrigerator
cabinet
with a "P" clamp.
5.
Using a cordless
drill, drill a 1/4" hole in the cold water
pipe you
have selected.
B
C
D
E
F
G
u
D
6.
A. Co/c/water
pipe
B, Pipe e/amp
C, Copper
tubing
D, Compression
nut
E, Compression
s/eeve
F, Shutoff
va/ve
G, Packing
nut
Fasten the shutoff
valve
to the cold water
pipe with the pipe
clamp.
Be sure the outlet end is solidly
in the 1/4,,drilled
hole in
the water
pipe and that the washer
is under the pipe clamp.
Tighten
the packing
nut. Tighten
the pipe clamp
screws slowly
and evenly so the washer
makes a watertight
seal. Do not
overtig hten.
3.
A. Copper
tubing
B. "P" e/amp
C, Compression
nut
D. Compression
s/eeve
Turn on water
supply to refrigerator
and check for leaks.
Correct
any leaks.
Publicidad
Tabla de contenido
