brondell Capella Manual Del Proprietário página 30

TECHNICAL INFORMATION
Performance Data Sheet
Volatile Organic Chemicals (VOCs) Included by Surrogate Testing*
Chemical
alachlor
atrazine
benzene
carbofuran
carbon tetrachloride
chlorobenzene
chloropicrin
2,4-D
dibromochloropropane(DBCP)
o-dichlorobenzene
p-dichlorobenzene
1,2-dichloroethane
1,1-dichloroethylene
cis-1,2-dichloroethylene
trans-1,2-dichloroethylene
1,2-dichloropropane
cis-1,3-dichloropropylene
dinoseb
endrin
ethylbenzene
ethylene dilbromide (EDB)
haloacetonitriles (HAN)
bromochloroacetonitrile
dibromoacetonitrile
dichloroacetonitrile
trichloroacetoritrile
haloketones (HK):
1,1-dichloro-2-propanone
1,1,1-trichloro-2-propanone
heptachlor
heptachlor epoxide
hexachlorobutadiene
hexachlorocyclopentadiene
lindane
methoxychlor
pentachlorophenol
simazine
styrene
1,1,2,2-tetrachloroethane
tetrachloroethylene
toluene
2,4,5-TP (silvex)
tribromoacetic acid
1,2,4-trichlorobenzene
1,1,1-trichloroethane
1,1,2-trichloroethane
trichloroethylene
chloroform (surrogate
chemical)
bromoform
bromodichloromethane
chlorodibromomethane
xylenes (total)
* Chloroform was used as the surrogate chemical for VOC reduction claims.
1. These harmonized values were agreed upon by representatives of USEPA and
Health Canada for the purpose of evaluating products to the requirements of
this Standard.
2. Influent challenge levels are average influent concentrations determined in
surrogate qualification testing.
3. Maximum product water level was not observed but was set at the detection limit
of the analysis.
28
Drinking Water Influent Challenge
Regulatory level¹ Concentration²
(MCL/MAC) mg/L mg/L
0.002 0.050
0.003 0.100
0.005 0.081
0.040 0.190
0.005 0.078
0.100 0.077
– 0.015
0.070 0.110
0.0002 0.052
0.600 0.080
0.075 0.040
0.005 0.088
0.007 0.083
0.070 0.170
0.100 0.086
0.005 0.080
– 0.079
0.007 0.170
0.002 0.053
0.700 0.088
0.00005 0.044
– 0.022
– 0.024
– 0.0096
– 0.015
– 0.0072
– 0.0082
0.0004 0.025
0.0002 0.0107 6
– 0.044
0.050 0.060
0.0002 0.055
0.040 0.050
0.001 0.096
0.004 0.120
0.100 0.150
– 0.081
0.005 0.081
1.000 0.078
0.050 0.270
– 0.042
0.070 0.160
0.200 0.084
0.005 0.150
0.005 0.180
trihalomethanes (includes):
0.080 0.300
10 0.070
4. Maximum product water level is set as a value determined in surrogate
qualification testing.
5. Chemical reduction percent and maximum product water level calculated at
chloroform 95% break through point as determined in surrogate qualification
testing.
6. The surrogate test results for heptachlor epoxide demonstrated a 98% reduction.
These data were used to calculate an upper occurrence concentration which
would produce a maximum product water level at the MCL.
Maximum
Chemical Reduction
Product Water
Percent (%)
Concentration mg/L
> 98 0.001
> 97 0.003
> 99 0.001
> 99 0.001
98 0.0018
> 99 0.001
99 0.0002
98 0.0017
> 99 0.00002
> 99 0.001
> 98 0.001
95 0.0048
5
> 99 0.001
> 99 0.0005
> 99 0.001
> 99 0.001
> 99 0.001
99 0.0002
99 0.00059
> 99 0.001
> 99 0.00002
98 0.0005
98 0.0006
98 0.0002
98 0.0003
99 0.0001
96 0.0003
> 99 0.0001
98 0.0002
> 98 0.001
> 99 0.000002
> 99 0.00001
> 99 0.0001
> 99 0.001
> 97 0.004
> 99 0.0005
> 99 0.001
> 99 0.001
> 99 0.001
99 0.0016
> 98 0.001
> 99 0.0005
95 0.0046
> 99 0.0005
> 99 0.0010
95 0.015
> 99 0.001
3
3
3
3
4
3
3
4
3
3
3
5
3
3
3
3
3
4
4
3
3
3
3
3
3
3
3
6
3
3
3
3
3
3
3
3
3
3
4
3
3
4
3
3
3