Flex LBR 1506 VRA Manual Del Usuario página 12

Safety instructions for sander
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=
áå ~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
 Hold the device by the insulated grip
surfaces, as the sanding belt may come
into contact with the power cord itself.
A damaged live cable may cause metal
parts of the device to become live and
result in an electric shock.
 Do not use the electric power tool
if it has a damaged power cord.
Do not touch the damaged power
cord and pull out the mains plug if the
power cord is damaged during work.
Damaged power cords increase the risk
of an electric shock.
 Use the electric power tool for dry
sanding only. If water penetrates the elec-
tric power tool, there is an increased risk
of electric shock.
 When working, guide the electric power
tool with both hands. The handle must
be attached! Do not switch on the machine
until both hands are in the grip position.
 Keep hands away from the running
sanding belt. There is a risk of injury
caused by crushing in the area
of the guide rollers.
On account of the operating mode and
the guaranteed flexibility of the power tool
these danger areas cannot be completely
shielded.
 Dust released from materials, such
as lead paints, some types of wood,
minerals and metal, may be hazardous
to the operator or people in the vicinity.
Inhaling or touching these dusts may result
in respiratory diseases and/or allergic
reactions.
12
– Ensure the work place is well ventilated!
– If possible, use external dust extraction.
– It is recommended to wear a respirator
mask belonging to filter class P2.
 Do not work on materials which release
hazardous substances (e.g. asbestos).
 Never grind or cut light metals which have
a magnesium content greater than 80%.
Risk of fire!
 If power tools are used outdoors or are
exposed to excessive amounts of metal
dust, connect them via a residual-current-
operated circuit-breaker (tripping current
maximum 30 mA). Do not use any worn,
torn or severely clogged sanding belts.
Damaged sanding belts may rip, fly off and
cause an injury.
 Before using the machine, check that
the grinding tools have been installed and
secured correctly. Switch on the machine
at no load for 30 seconds!
 Interrupt the test run immediately if violent
vibrations occur or other damage is esta-
blished. Check the machine to determine
the cause.
 Do not load the electric power tool to such
an extent that it comes to a standstill or the
sanding belt slips.
 Before putting down the power tool, switch
it off and wait until it comes to a standstill.
 Do not clamp the power tool in a vice.
 Always lay the power cord to the rear away
from the electric power tool.
 Clamp the workpiece if it is loose or not
positioned securely by its own weight.
 Store and handle grinding tools according
to the manufacturer's instructions.
LBR 1506 VRA