Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GAM 270 MFL Professional Manual De Instrucciones

OBJ_BUCH-2370-003.book Page 23 Tuesday, February 16, 2016 3:45 PM
Calibration for Horizontal Surfaces (see figure I)
The surface onto which you place the measuring tool must not deviate from
the horizontal line by more than 5°. If the deviation is greater, the calibration
process is discontinued with the indication "---" .
 Switch the measuring tool on and position it on the horizontal surface in
such a manner that the spirit level 9 faces upward and the display 7
faces you. Wait for 10 s.
 Then press the "Cal" calibration button 20 for approx. 2 seconds until
"CAL1" appears briefly on the display. Then the measuring value will
flash on the display.
 Turn the measuring tool by 180° around the vertical axis so that the
spirit level still faces upward, but the display 7 faces away from you.
Wait for 10 s.
 Then press the calibration button "Cal" 20 again. "CAL2" is briefly indi-
cated in the display. Afterwards, the measuring value appears in the
display (no longer flashing). The measuring tool is now re-calibrated for
this supporting surface.
Note: If during step  the measuring tool is not turned around the axis illus-
trated in the figure, the calibration cannot be completed ("CAL2" does not
appear on the display).
Calibration for Vertical Surfaces (see figure J)
The surface onto which you place the measuring tool must not deviate from
the vertical line by more than 5°. If the deviation is greater, the calibration
process is discontinued with the indication "---".
 Switch the measuring tool on and position it on the vertical surface in
such a manner that the spirit level 10 faces upward and the display 7
faces you. Wait for 10 s.
 Then press the "Cal" calibration button 20 for approx. 2 seconds until
"CAL1" appears briefly on the display. Then the measuring value will
flash on the display.
 Turn the measuring tool by 180° around the vertical axis so that the
spirit level still faces upward, but the display 7 faces away from you.
Wait for 10 s.
 Then press the calibration button "Cal" 20 again. "CAL2" is briefly indi-
cated in the display. Afterwards, the measuring value appears in the dis-
play (no longer flashing). The measuring tool is now re-calibrated for
this supporting surface.
Note: If during step  the measuring tool is not turned around the axis illus-
trated in the figure, the calibration cannot be completed ("CAL2" does not
appear on the display).

Maintenance and Service

Maintenance and Cleaning

For safe and proper working, always keep the measuring tool clean.
Store and transport the measuring tool only in the supplied protective pouch.
Do not immerse the measuring tool in water or other fluids.
Wipe off debris using a moist and soft cloth. Do not use any cleaning agents
or solvents.
When the measuring tool is exposed to rain for an extended period, its func-
tion may be impaired. However, after completely drying off, the measuring
tool is ready for operation. No calibration is required.
In case of repairs, send in the measuring tool packed in its protective pouch
22.

After-sales Service and Application Service

Our after-sales service responds to your questions concerning maintenance
and repair of your product as well as spare parts. Exploded views and infor-
mation on spare parts can also be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions concerning our
products and their accessories.
In all correspondence and spare parts orders, please always include the
10-digit article number given on the nameplate of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of
a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Bosch Power Tools
English | 23
1 609 92A 25B | (16.2.16)