Ryobi LLCD1402 Manual De Utilización página 7

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
GB
FR
DE
ES
IT
OPERATION
ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 3.
The bit rotation is reversible and is controlled by a
selector located above the switch trigger. With the drill
held in normal operating position, the rotation selector
should be positioned to the left of the switch trigger for
forward drilling. The drilling direction is reversed when
the selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when
not in use.
CAUTION:
To prevent gear damage, always allow the chuck
to come to a complete stop before changing the
direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
NOTE: The drill will not run unless the rotation selector is
pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage
may cause the drill to become overheated. If this occurs,
cool the drill by running it without a load and at full speed.
KEYLESS CHUCK
See Figure 4.
The drill has a keyless chuck to tighten or release drill
bits in the chuck jaws. The arrows on the chuck indicate
which direction to rotate the chuck body in order to LOCK
(tighten) or UNLOCK (release) the drill bit.
WARNING
Do not hold the chuck with one hand and use the
power of the drill to tighten the chuck jaws on the
drill bit. The chuck body could slip in your hand,
or your hand could slip and come in contact with
the rotating drill bit. This could cause an accident
resulting in serious personal injury.
TWO-SPEED GEAR SWITCH (HI-LO)
See Figure 5.
A slide switch is located on top of the drill to select either
LO (1) or HI (2) speed. When using drill in the LO (1)
speed range, speed will decrease and unit will have more
power and torque. When using drill in the HI (2) speed
range, speed will increase and unit will have less power
NL
PT
DK
SE
FI
NO
English
RU
PL
CZ
HU
RO
LV
and torque. Use LO (1) speed for high power and torque
applications and HI (2) speed for fast drilling or driving
applications.
ADJUSTABLE TORQUE CLUTCH
This product is equipped with an adjustable torque
clutch for driving different types of screws into different
materials. The proper setting depends on the type of
material and the size of screw you are using.
ADJUSTING TORQUE
See Figure 6.
There are twenty-four torque indicator settings located on
the front of the drill.
Rotate the adjusting ring to the desired setting.
• 1 - 4
For driving small screws
• 5 - 8
For driving screws into soft material
• 9 - 12
For driving screws into soft and hard
materials
• 13 - 16
For driving screws into hard wood
• 17 - 20
For driving large screws
• 21-
For drilling
BIT STORAGE
See Figure 7.
When not in use, bits provided with the drill can be placed
in the storage area located on the base of the drill.
INSTALLING BITS
See Figures 8 - 9.
Lock the switch trigger by placing the rotation selector
in the center position.
Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend
to use. Also, raise the front of the drill slightly to keep
the bit from falling out of the chuck jaws.
Insert the drill bit.
WARNING
Make sure to insert the drill bit straight into the
chuck jaws. Do not insert the drill bit into the
chuck jaws at an angle then tighten, as shown
in figure 9. This could cause the drill bit to be
thrown from the drill, resulting in possible serious
personal injury or damage to the chuck.
3
LT
EE
HR
SI
SK
GR
TR

Publicidad

Tabla de contenido
loading

Tabla de contenido