Troubleshooting Guide; Accessories And Spare Parts; Warranty; Technical Data - Kärcher HD 6/15 MXA Manual De Instrucciones

5. Remove the hose stopper from the high-pressure
hose.
6. Pull out locking hook.
Figure K
Locking hook
1
Hose connection
2
High-pressure hose.
3
7. Pull high-pressure hose out of the hose connection.
8. Insert new high-pressure hose through the two hose
guide rollers and insert into the hose connection.
Observe the direction of rotation of the hose reel.
Figure L
Hose guide roller
1
9. Insert the locking hook into the hose connection.
10. Check that all washers are behind the locking hook.
11. Fit the hose stopper to the other end of the high-
pressure hose. Distance to the end of the hose
about 1 m (to the high-pressure gun).
12. Hold the hose reel and remove the Allen key.
13. Unlock the hose reel by pulling on the high-pressure
hose and let the high-pressure hose slowly roll up.
Control the reeling speed by holding the hose.
14. Replace the cover.

Troubleshooting guide

DANGER
Risk of injury due to inadvertently starting up de-
vice and also due to electric shock.
Switch off the device immediately and unplug the mains
plug before performing work.
Have electrical components checked and repaired by
the authorised Customer Service.
In case of any malfunctions not mentioned in this chap-
ter, contact the authorised Customer Service when in
doubt or when you have been explicitly advised to do
so.
Device does not start
 Check the power cable for damage.
 Check the mains voltage.
 If the device overheats:
a Set the power switch to "0".
b Allow the device to cool for at least 15 minutes.
Country variant
Country
Electrical connection
Voltage
Phase
Frequency
Connection output
Degree of protection
Power protection (slow-blowing)
Extension cable, 30 m
Water connection
Feed pressure (max.)
 Contact Customer Service in the case of electrical
Device does not reach required pressure
 Check the size of the nozzle and compare with the
 Vent the device, see section "Venting the device".
 Clean the sieve in the water connection.
 Check the water supply volume and compare with
 Clean the nozzle.
 Contact Customer Service if necessary.
Pump leaking
Up to 3 drops of water per minute are permissible.
 In case of more serious leaks, have the device
Pump knocking
 Check the water supply line for leaks.
 Vent the device, see section "Venting the device".
 Contact Customer Service if necessary.
Detergent dosing volume too low
 Refill the foam nozzle cup.
 Plug a larger blender onto the suction hose.
 Check the suction hose and foam nozzle for deter-
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

HD 6/15 HD 6/15
MXA MXA
EU CH
V 230 230
~ 1 1
Hz 50 50
kW 3,1 2,3
IPX5 IPX5
A 16 10
2
mm 2,5 2,5
MPa 1 1
English
c Set the power switch to "1".
faults.
required size specified in the "Technical data" sec-
tion.
the required volume specified in the "Technical data"
section.
checked by Customer Service.
gent deposits. Remove deposits using lukewarm
water.

Accessories and spare parts

Warranty

HD 7/17 HD 6/ HD 7/
MXA 16-4 14-4
MXA MXA
EU EU EU
400 230 230
3 1 1
50 50 50
4,2 3,3 3,4
IPX5 IPX5 IPX5
16 16 16
2,5 2,5 2,5
1 1 1
HD 7/ HD 8/
16-4 18-4
MXA MXA
EU EU
400 400
3 3
50 50
4,2 4,6
IPX5 IPX5
16 16
2,5 2,5
1 1
15