General Recommendations - BIEMMEDUE SUMMER 18 Manual Para El Usuario Y El Mantenimiento

GB
Before using the heater, read and understand all instructions and follow them carefully. The manufacturer is not responsible for
EC
15
14
1 COMBUSTION CHAMBER
2 BURNER
3 NOZZLE
4 HANDLE (Summer 18)
5 SOLENOID VALVE
6 DIESEL PUMP

GENERAL RECOMMENDATIONS

SUMMER and EC heaters are to be run on heating with light diesel
oil. SUMMER heaters produce warm air mixed with combustion gases,
EC heaters produce pure warm air since they are equipped with a chim-
ney connection to canalise the combustion gases outside via a flue.
Always follow local ordinances and codes when using this heater.
• read and follow this owner's manual before using the heater.
• use only in places free of flammable vapours or high dust content.
• never use heater in immediate proximity of flammable materials.
Minimum clearance 2.50 m.
• make sure fire fighting equipment is readily available.
• make sure sufficient fresh outside air is provided according to
the heater requirements. They should only be used in well venti-
lated areas in order to avoid carbon monoxide poisoning.
• never block air inlet (rear) or air outlet (front).
• in case of very low temperatures add kerosene to the heating oil.
• make sure heater is always under surveillance and keep children
and animals away from it.
• before starting the heater always check free rotation of ventilator.
• unplug heater when not in use.
OPERATION
Before any attempt of starting the heater is made, check that your
electrical supply conforms to the data on the model plate.
Warning
Mains must be fitted with a thermo-magnetic differren-
tial switch.
Unit plug must be linked to a socket with a mains
switch.
The heater can run automatically when connected to a control de-
vice such as thermostat, time clock. Connection of controller is made
through cable protection (12) at connectors F3 and F4 of the electronic
flame control box. This bridge should be kept and retrofitted if manual
running of heater is whished at another time.
To start heater, connect to mains, set control device at desired val-
ue, set switch (11) on position
damages to goods or persons due to improper use of units.
SUMMER
1
13
16
Fig.1
7 MOTOR
8 FAN
9 FUEL FILTER
10 FUEL CIRCUIT
11 SUPPORT AND HANDLE (Optional for Summer 18)
12 WHEEL (Optional for Summer 18)
: the ventilator starts, immediately fol-
IMPORTANT
1 2
12
lowed by ignition. When unit is started for the first time or is started af-
ter the oil tank has been totally emptied, the flow of oil to the burner
may be impaired by air in the circuit. In this case the control box will cut
out the heater and it might be necessary to renew the starting procedure
once or twice by depressing the button (11) in on position "0" and
pressing the button in the position
Should the heater not start, check that oil tank is full. Press the but-
ton on position "0" and restat the space heater pressing the button on
position .
Should the heater still not work, please refer to chapter "OBSERVED
FAULTS, CAUSES AND REMEDIES".
Warning
If the voltage supply is less than 190 V, the space heater
automatically stops and the lamp flashes. The space
heater can automatically restart when the voltage goes
up again to 205 V.
STOPPING THE HEATER
Set main switch (11) on "0" position or turn thermostat or other
control device on lowest setting.
SAFETY DEVICES
The unit is fitted with an electronic flame control box. In case of
malfunction this box will cut in and stop the heater, at the same time
the alarm lamp (13) in the control box reset button (11) will light up.
You will have to depress button (11) in the position "0" on control
box before being able to restart the heater.
TRANSPORT
Warning
Before making any attempt to restart heater find and
eliminate reason of overheating.
12
3 4 5 6 7
13 FUEL TANK
14 MAIN SWITCH
15 CONTROL LAMP
16 PPREDISPOSITION FOR CABLE FASTENER
ROOM THERMOSTAT
.
8
9
10
11