Sanding Tool Safety; Product Familiarisation; Included Accessories - Silverline 264125 Manual De Instrucciones

264125
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
g) When used in Australia or New Zealand, it is recommended that this tool is
ALWAYS supplied via Residual Current Device (RCD) with a rated residual
current of 30mA or less.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention wh*/=ile operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
4) Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
150W Orbital Sander
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.

Sanding Tool Safety

• Before connecting the tool to a power source, ensure that the voltage supply
matches that specified on the rating plate of the tool
• Always wear appropriate protective equipment, including a dust mask with a
minimum FFP2 rating, safety goggles and ear defenders
• Ensure all people in the vicinity of the work area are also equipped with suitable
personal protective equipment
• Take special care when sanding some woods (such as beech, oak, mahogany
and teak), as the dust produced is toxic and can cause extreme reactions
• Do not sand magnesium or alloys containing a high percentage of magnesium
• Be aware of paint finishes or treatments that may have been applied to the
material that is being sanded. Many treatments can create dust that is toxic, or
otherwise harmful. If working on a building constructed prior to 1960, there is
an increased chance of encountering lead-based paints
• The dust produced when sanding lead-based paints is particularly hazardous
to children, pregnant women, and people with high blood pressure. Do not
allow these people near to the work area, even if wearing appropriate personal
protective equipment
• Whenever possible, use a vacuum dust extraction system to control dust and
waste
• Be especially careful when using a machine for both wood and metal sanding.
Sparks from metal can easily ignite wood dust. Always clean your machine
thoroughly to reduce the risk of fire
• Work surfaces and sandpaper can become very hot during use, if there is
evidence of burning (smoke or ash) from the work surface, stop and allow the
material to cool. Do not touch the work surface or sandpaper until they have
had time to cool
• Do not touch the moving sanding paper
• Always switch off before placing the sander down
• Always unplug the sander from the mains power supply before changing or
replacing sandpaper
• Even when this tool is used as prescribed it is not possible to eliminate all
residual risk factors. If you are in any doubt as to safe use of this tool, do not
use it

Product Familiarisation

1 On/Off Trigger Switch
2 Lock-On Button
3 Sanding Base
4 Quick-Change Levers for Conventional Sanding Sheets
5 Dust Extraction Adapter
6
Main Handle
7
Front Handle

Included accessories:

1 hook and loop sanding sheet (100 grit),
1 conventional sanding sheet (100 grit)
www.silverlinetools.com
1 ⁄ Sheet
3
5