Silverline 763565 Manual De Instrucciones página 7

763565
Air supply connection
QUICK COUPLER
TO YOUR
NIPPLE
AIR TOOL
RECOIL HOSE
LEADER HOSE
• This tool should be connected to a clean, dry air supply with inline oiler and water separator
• Do not allow supply pressure to exceed the maximum stated (see "Specifications")
• Ensure that water is drained from air system daily
• Ensure that all parts of the system (hoses, couplers, etc .) are correctly rated for the air pressure
to be used
Setting tool power
• The tool speed/power can be adjusted by reducing/increasing the air supply pressure within
the range specified in 'Specifications' . Further speed adjustments are made by turning the Air
Restrictor (3)
• Whilst working with the tool, speed adjustments can be made via the Speed Control Trigger (2)
Fitting a sanding sheet
1 . Select sanding sheet of the correct grit for the task
2 . Clamp each end of the sheet under the Front and Rear Clamps (7 & 5)
3 . Ensure the abrasive paper is pulled tight against the Sanding Pad (6) and aligned so that the pad
is completely covered
Operation
1 . We recommend that you test the machine on scrap material prior to starting work on the
workpiece
2. Grip the main handle firmly with one hand, so that you can easily operate the Speed Control
Trigger (2)
3 . Squeeze the speed control gently to get used to the way the tool operates
4 . You can adjust the speed of the tool by adjusting the pressure you apply to the Speed Control
Trigger
5 . Begin by bringing the abrasive paper gently into contact with the workpiece, and slowly build up
speed and pressure
Note: The friction between abrasive paper and material will cause heat . Check the workpiece
frequently to ensure it does not burn .
Note: DO NOT allow the tool to run in 'idle rotation' for an extended period of time. This will
shorten its life .
WARNING: Be aware that air tools may hold residual pressure after use . Always bleed air pressure
from the tool after shutting off air supply .
Accessories
• Accessories for this tool are available from your Silverline stockist
• Spare parts can be obtained from your Silverline dealer or toolsparesonline .com
WATER SEPARATION
NIPPLE
OILER
DRAIN DAILY
REGULATOR AIR SUPPLY
Air Orbital Jitterbug Sander
Maintenance
WARNING: Always disconnect from the air supply and depressurise before cleaning or carrying out
any maintenance .
Cleaning
• Keep your tool clean at all times . Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life . Clean the body of your machine with a soft brush, or dry cloth
IMPORTANT: There is very little that can go wrong with your air tool and it should be noted that
when an air tool fails to work it is generally because the internal workings have corroded due to
dirty, wet air and failure to follow the instructions given below .
Daily maintenance procedure: Disconnect from the air supply, pour the equivalent of a
tablespoon of oil into the air intake . Operate the machine at low speed to thoroughly lubricate all
internal workings .
• If the machine is in constant use or used for long periods at a time, a combined filter/lubricator
must be fitted. There must be an air filter fitted at all times
• Use air tool oil . DO NOT UNDER ANY CIRCUMSTANCES USE NORMAL ENGINE OIL
• Failure to comply with the operating and maintenance instructions may invalidate the guarantee
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools .com/en-GB/Support
Address:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• When you store the machine use, always ensure there is oil in the inline oiler . If necessary, top up
the oil before packing the machine away neatly in its case
• Failure to comply with the operating and maintenance instructions may invalidate the guarantee
• Always store the machine neatly in the case provided
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
• Air tools should not be disposed of with household waste
• Air tools may contain traces of tool oil and other lubricants and so must be recycle accordingly
• Contact your local waste disposal authority for information on the correct way to dispose of
air tools
silverlinetools.com
7