Tabla de contenido
Publicidad
- clean cutting blade M and cutting guard N after each
use
- clean ventilation slots AH regularly with a brush or
compressed air
•
Storage d
- store the tool indoors in a dry and locked-up place, out
of reach of children
- securely mount storage rail AK on the wall with 2
screws (not supplied) and horizontally leveled
- make sure that hook AL is mounted together with rail
AK
- store the tool by hanging it on the storage hook AL
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
•
Be aware that damage due to overload or improper
handling of the product will be excluded from the
warranty (for the SKIL warranty conditions see
www.skil.com or ask your dealer)
TROUBLESHOOTING
•
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! in case of electrical or mechanical malfunction,
immediately switch off the tool and remove battery
Tool does not operate
- empty battery -> charge battery
- hot battery -> let battery cool down
- internal fault -> contact dealer/service station
Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/off switch defective -> contact dealer/service station
Tool vibrates abnormally
- grass/brushwood too high -> cut in stages
Tool does not cut
- line too short/broken off -> feed the line manually
Line cannot be fed
- spool empty -> replace spool
- line entangled inside spool -> inspect spool; rewind if
necessary
Line is not cut off to correct length -> remove cover from
cutting blade
Line keeps breaking
- line entangled inside spool -> inspect spool; rewind if
necessary
- trimmer incorrectly used -> only trim with the tip of the
line; avoid stones, walls and other hard objects; feed
the line regularly
ENVIRONMENT
•
Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 9 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
•
When using tool as line trimmer
Measured in accordance with EN 60335 the sound
pressure level of this tool is 82.5 dB(A) (uncertainty
K = 2.5 dB) and the sound power level 93.8 dB(A)
(uncertainty K = 1.44 dB), and the vibration 5.1 m/s²
(triax vector sum; uncertainty K = 1.5 m/s²)
•
When using tool as brush cutter
Measured in accordance with ISO 11806-1 the sound
pressure level of this tool is 93.9 dB(A) (uncertainty
K = 4.1 dB) and the sound power level 95.3 dB(A)
(uncertainty K = 0.92 dB), and the vibration 7.5 m/s²
(triax vector sum; uncertainty K = 1.5 m/s²)
•
The vibration emission level has been measured in
accordance with a standardised test given in EN 60335
/ ISO 11806-1; it may be used to compare one tool with
another and as a preliminary assessment of exposure
to vibration when using the tool for the applications
mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Débroussailleuse/coupe-
bordure sans fil à moteur
sans balai
INTRODUCTION
•
Équipé de la lame de coupe métallique, cet outil est
destiné aux broussailles, buissons, ronces et autre
végétation du même type
•
Équipé du système de bobine, cet outil est destiné
à couper les herbes et mauvaises herbes sous les
buissons ainsi que sur les pentes et les bordures qui ne
peuvent être atteintes avec une tondeuse
•
Cet outil n'est ni destiné à couper ou hacher des fleurs, ni
à des fins de compostage
•
Cet outil n'est pas conçu pour un usage professionnel
•
Vérifiez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
•
Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
•
Lisez attentivement ce manuel d'instruction avant
d'utiliser l'outil et conservez-le pour pouvoir vous y
référer ultérieurement 3
16
0255
Publicidad
Tabla de contenido
