Heath Zenith Secure Home DualBrite SH-5318 Manual De Instrucciones
Heath Zenith Secure Home DualBrite SH-5318 Manual De Instrucciones

Heath Zenith Secure Home DualBrite SH-5318 Manual De Instrucciones

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Motion Sensor
Light Control with
2-Level Lighting
Models SH-5318
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• D
B
Timer.
®
ual
rite
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
This package includes:
Lamp Holders
Cover Plate
Light Control
Mounting Bolt
Mounting Strap
2 Shells*
* Model SL-5318 only
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a
qualified electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
© 2007 HeathCo LLC
D
B
ual
rite
Rubber Plug
Plastic Hanger
Sensor
2 Wire
Connectors
Gasket
6 Screws
(3 sizes included)
OPERATION
®
Mode:
On-Time
Test
5 Seconds
Auto
1, 5, or 20 Min
Manual
To Dawn*
Accent
3, 6 Hr, to Dawn
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1
the circuitry to calibrate.
Put ON-TIME switch
on the sensor bottom
to TEST and the D
B
switch OFF.
®
rite
Put the ON-TIME switch in the 1, 5,
or 20 minute position.
MANUAL MODE
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.
Mode Switching Summary
TEST
AUTO
MANUAL MODE
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
D
ual
Light comes on half bright for selected time after dusk
(Off, 3 hr., 6 hr., until dawn). Selecting OFF disables
this feature. The motion sensing features will continue
to work as described in this manual. If motion is sensed,
the light turns on full bright for the ON-TIME (1, 5, or
20 minutes) then returns to dim mode.
Works: Day Night
/
minutes for
1
2
TEST
ON-TIME
D
ual
-
ual
TEST 1 5 20
Off 3 6 Dusk to
AUTO
ON-TIME
TEST 1 5 20
1 Second OFF
... back on.
Move ON-TIME Switch to
1, 5, or 20 minutes
Flip light switch off
for one second then
back on*
B
Timer
®
rite
598-1154-01
x
x
x
x
x
B
®
rite
Dawn
then...

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Heath Zenith Secure Home DualBrite SH-5318

  • Página 1 OPERATION ® rite Mode: On-Time Works: Day Night Motion Sensor Test 5 Seconds Auto 1, 5, or 20 Min Light Control with Manual To Dawn* Accent 2-Level Lighting 3, 6 Hr, to Dawn * resets to Auto Mode at dawn. Note: When first turned on wait about 1 minutes for Models SH-5318...
  • Página 2 INSTALLATION ❒ Twist the junction box wires and fixture wires together as shown. Secure with wire connectors. For easy installation, select an existing light with a wall White to Mounting Black to switch for replacement. Strap White Black Rubber Plug Wall Mount Eave Mount Mounting...
  • Página 3 TEST AND ADJUSTMENT ❒ Loosen the clamp screw in the Clamp sensor ball joint and gently Screw ❒ Turn on the circuit breaker and light switch. rotate the sensor. ❒ Walk through the coverage NOTE: Sensor has a 1 minute warm up period Ball area noting where you are Joint...
  • Página 4: Troubleshooting Guide

    TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE SYMPTOM POSSIBLE CAUSE Lights will not come Lights stay on 1. Light switch is turned off. 1. A flood lamp is positioned too close to continuously. 2. F l o o d l i g h t i s l o o s e o r the sensor or pointed at nearby objects burned out.
  • Página 5: Funcionamiento

    Control de luz Nota: Cuando lo prenda por primera vez espere 1 minutos para que el circuito se claibre. y detector de Para PRUEBA: movimiento D ® Ponga el interruptor de ON-TIME ® rite rite tiempo (ON-TIME), al fondo del detector, en Modelos SH-5318 la posición de prueba TEST 1 5 20...
  • Página 6: Instalacion

    INSTALACION ❒ Conecte los cables de la caja de empalme con los cables del aparato de luz, como se muestra. Tuérazalos Para una fácil instalación escoja una luz con un juntos y asegúrelos con un conector de cables. interruptor de pared. Negro a Negro Blanco a Blanco Enchufe...
  • Página 7: Prueba Y Ajuste

    PRUEBA Y AJUSTE ❒ Afloje el tornillo sujetador en la Tornillo unión esférica y gire despacio Sujetador ❒ Prenda el cortacircuitos y el interruptor de luz. el detector. ❒ Camine por el área a prote- NOTA: El detector tiene un período de cerca de 1 Unión gerse y dése cuenta dónde minutos de calentamiento antes de detectar...
  • Página 8: Guia De Investigacion De Averias

    GUIA DE INvESTIGACION DE AvERIAS SINTOMA POSIBLE CAUSA SINTOMA POSIBLE CAUSA La luz no se enci- La luz se queda 1. El interruptor de luz está apaga- 1. Un faro está colocado demasiado cerca ende. prendida con- al detector o apunta a objetos cercanos 2.

Tabla de contenido