Tabla de contenido
Publicidad
Enlaces rápidos
Publicidad
Tabla de contenido
Manuales relacionados para Shindaiwa LE2510
Resumen de contenidos para Shindaiwa LE2510
- Página 1 SHINDAIWA OWNER’S/OPERATOR’S MANUAL LE2510 LAWN EDGER LE2510 WARNING! Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit. Part Number 81719 Rev. 2/07...
-
Página 2: Tabla De Contenido
IMPORTANT! Rotating blade may cause injury. Blade may continue Shindaiwa Inc. reserves the right to make A statement preceded by the word to rotate after unit is shut off. changes to products without prior notice, “IMPORTANT”... -
Página 3: Safety Instructions
Do not use attachments not WARNING! that no fuel leaks from around the fuel cap approved by Shindaiwa for use on this unit. and/or fuel tank. If fuel leaks are evident, The engine exhaust from this stop using the unit immediately. Fuel leaks... -
Página 4: Safety Labels
BEWARE OF THROWN OR RICHOCHETED OBJECTS KEEP AWAY FROM ROTATING BLADE Shindaiwa P/N 19422-00046 LE2510 IMPORTANT Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged or miss- ing information labels. New labels are available from your local authorized Shindaiwa dealer. -
Página 5: Product Description
Product Description Using the accompanying illustrations as LE2510 LAWN EDGER a guide, familiarize yourself with this unit Throttle Ignition and its various components. See Figure 4. Interlock Switch Understanding your unit helps ensure top Grip performance, long service life, and safer operation. -
Página 6: Assembly And Adjustments
Assembly and Adjustments Install Gearcase Assembly 1. Loosen gearcase clamp screw. . Remove the gearcase index screw. . Slide the gearcase oriented as shown in Figure 5 onto the shaft tube insuring that the flex drive is engaged in the gearcase. NOTE: It may be necessary to pull the flex cable out from the shaft tube, engage into the gearcase... -
Página 7: Mixing Fuel
ISO-L- 50:1 gasoline/oil ratio. be used in your Shindaiwa engine. EGD performance requirements. Shindaiwa One is recommended for use in all Shindaiwa low emissions engines.Shindaiwa One also includes a fuel stabilizer. Filling the Fuel Tank 1. -
Página 8: Starting The Engine
Starting the Engine IMPORTANT!! Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP. WARNING! Never start the en- gine from the operating position. Make sure the cutting attatchment is clear of... -
Página 9: Stopping The Engine
Idle Adjusting Screw in the field. to your Shindaiwa dealer for inspection. Figure 15 Checking Unit Condition NEVER operate the unit with the cutting Use only authorized Shindaiwa parts and... -
Página 10: Using A Hand Held Edger
Never adjust the guide wheel while the engine is running. NOTE Guide wheel adjustment is also required to compensate for blade wear. The numbers are for WARNING! reference only; they do NOT refer to depth in Figure 17a inches Use only Shindaiwa replacement Figure17 edger blades. -
Página 11: General Maintenance
General Maintenance IMPORTANT! NOTE: Using non-standard replacement parts could WARNING! MAINTENANCE, REPLACEMENT OR invalidate your Shindaiwa warranty. REPAIR OF EMISSION CONTROL Before performing any maintenance, re- DEVICES AND SYSTEMS MAY BE Muffler pair or cleaning work on the unit, make... - Página 12 . Slide the gearcase and shield assembly out. Use only lithium-base grease such Shindaiwa-trained service technician. from the shaft tube. as Shindaiwa Gear Case Lubricant or equivalent. See Figure 0. 4. Pull the flexible shaft from the shaft tube assembly, and clean the shaft thoroughly in solvent.
- Página 13 It is highly recommended clearance adjustment did not change as that this is done by a Shindaiwa-trained a result of tightening locknut. Readjust service technician. as necessary.
-
Página 14: Replacing The Edger Blade
Figure 5. and engine cover in the reverse order of If you note excessive carbon buildup, 5. Inspect the cylinder exhaust port for disassembly. consult with an authorized Shindaiwa any carbon buildup. servicing dealer. Replacing the Edger Blade Holder A . -
Página 15: Troubleshooting Guide
Troubleshooting Guide ENGINE DOES NOT START What To Check Possible Cause Remedy Faulty recoil starter. Fluid in the crankcase. Consult with an authorized servicing dealer. Internal damage. Loose spark plug. Tighten and re-test. Excess wear on cylinder, piston, rings. Consult with an authorized servicing dealer. Valves not seating. - Página 16 Troubleshooting Guide (continued) ADDITIONAL PROBLEMS Symptom Possible Cause Remedy Clogged air filter. Clean the air filter. Poor acceleration. Clogged fuel filter. Replace the fuel filter. Lean fuel/air mixture. Consult with an authorized servicing dealer. Adjust: 3,000 (±300) RPM (min -1 ). Idle speed set too low.
-
Página 17: Emission System Warranty
Shindaiwa Distributor. If any emission-related part is found defective during the warranty For the name and telephone number of the Shindaiwa Distributor in your period, it is your responsibility to present the product to an authorized area, please call Shindaiwa Inc. at (50) 69-070 between the hours of Shindaiwa dealer. - Página 18 11975 S.W. Herman Rd. Part Number 81719 Tualatin, Oregon 97062 USA 6-2-11, Ozuka-Nishi Asaminami-Ku, Hiroshima Revision 2/07 Telephone: 503 692-3070 731-3167, Japan Shindaiwa is a registered trademark of Shindaiwa, Inc. Fax: 503 692-6696 Telephone: 81-82-849-2220 Specifications subject to change without notice. www.shindaiwa.com Fax:...