Troubleshooting - Schumacher Electric DY-1420 Manual De Instrucciones

BATTERY SIZE/RATING
SMALL Motorcycle, Garden
BATTERIES
Tractor, etc.
CAR/TRUCKS 200 - 315 CCA
315 - 550 CCA
550 - 875 CCA
MARINE/
DEEP CYCLE
L.
Wheel Charger Assembly Instructions: (Instrucciones De Armado)
NOTE: Charger must be assembled before operating (Ante de la operación la unidad debe estar armada)
Parts (Piezas)
(2)10-32 screws (tornillos de corte rosca 10-32)
(2) 1/4-20 screws (tornillo de corte rosca 1/4-20)
(2) wheels (ruedas)
(2) axle caps (tapas del eje)
(1) handle (mango)
(1) mounting foot (pedestal de montaje)
(1) axle (del eje)
Tools necessary (Herramientas Necesarias)
1. First place the charger on it side.
2. Next mount the mounting foot FIG. A with (2) 1/4-20 screws, or FIG. F with (2) 10-32 screws.
3. Next pound the axle firmly into an axle cap using a hammer FIG. B.
4. Slide one wheel onto the axle with hub facing in, as shown in FIG. C.
5. Poke above assembly thru holes in charger back until axle sticks out of the other end.
6. Turn charger on its other side.
7. Slide wheel and pound cap onto the axle end.
8. Next turn the charger right side up onto its foot and wheels.
9. Remove the (2) top screws from each side of the charger, line up the handle and reinstall the screws FIG. E.
Primero coloque el cargador de lado.
A continuación monte el pedestal FIG. A con (2) tornillos 1/4-20.
A continuación golpee firmemente el eje dentro de la tapa del eje usando un martillo, FIG. B.
A continuación deslice las ruedas dentro del eje; los cubos deben estar orientados hacia adentro, FIG. C.
A continuación golpee la otra tapa del eje dentro del otro extreme del eje.
A continuación coloque el conjunto del eje dentro del fondo del cargador según se muestra en la FIG. C.
Monte el eje en el fondo del cargador usando los dos tornillo de corte de rosca 10-32 según se muestra en la FIG. D.
A continuación gire el cargador de la batería con el lado derecho hacia arriba sobre su pedestal y ruedas.
Saque los dos tornillos superiores de cada lado del cargador; alinee el mango y reinstale los tornillo. FIG. E.
If a problem does occur, check the following:
PROBLEM
No Meter Reading (AC Cord Unplugged)
Charger will not turn on when properly
connected.
Clicking noise from charger.
CHARGE RATE*/CHARGING TIME - HOURS**
2 AMP 10 AMP
6 - 12 AH 1.5 to 3 NR
12 - 32 AH 3 to 8
40 - 60 RC 11 to 15 2.5 to 3
60 - 85 RC 15 to 18 3 to 4
85 - 125 RC 18 to 25 4 to 5
55 MC 15 4
80 MC 19 5
105 MC 23 6
ASSEMBLY INSTRUCTIONS
5/16" wrench
3/8" wrench
Hammer
Screwdriver

TROUBLESHOOTING

POSSIBLE CAUSE
Clips are not making a good connection.
Battery voltage is too low.
2 amp charge rate being used
AC outlet is dead.
Poor electrical connection.
Circuit breaker is cycling.
Battery is defective.
Severely discharged battery but otherwise a good
battery.
Reverse connections at battery.
30 AMP 35 AMP 50 AMP 60 AMP
NR NR NR
.75 to 1 .5 to .75 NR
1 to 1.5 .75 to 1 .5 to .75 .5 to .63
1.5 to 1.7 1 to 1.5 .75 to 1 .63 to .75
NR NR NR
2 1.75 NR
2.5 2 NR
(Llave de 5/16")
(Llave de 3/8")
(Martillo)
(Destornillador)
SOLUTION
Rock clips back and forth for a better connection.
Plug AC line into outlet. Meter should now indicate.
None, meter will not indicate here.
Plug in a lamp to check for voltage.
Check connections, rock back and forth for a better
connection.
May be in the wrong switch position.
Have Battery checked.
Allow charging to continue until battery has a chance to
recover sufficiently to take a charge. If more that 20 min.
stop charging and have the battery checked.
Shut off charger and correct lead connections.
5
*Charge Rates for this model are listed on the
front panel.
**Based on battery at 50% charge.
NR
AH Ampere Hours
NR
NR Not Recommended
CCA Cold Cranking Amps
RC Reserve Capacity
MC Marine Capacity
NR
NR
NR
HUBS MUST
FACE IN
Fig. C
Fig. A
Fig. F
Fig. B
AXLE CAP
AXLE BRACKET
Fig. D
Fig. E