Husky CAT851 Manual De Funcionamiento Y Piezas página 6

Operations & Parts Manual
The amount of paint being applied can be varied by the speed
of the stroke, distance from the surface and adjustment of the
fluid control knob.
Overlap strokes just enough to obtain an even coat.
NOTE: Two thin coats of paint will yield better results and
have less chance of runs than one heavy layer.
Use a piece of cardboard as a shield to catch overspray at the
edges of the work to protect other surfaces.
The desired pattern and fine atomization can be easily
obtained by regulating the Pattern Adjusting Knob, Fluid
(PAINT) Adjusting Knob.
PATTERN ADJUSTMENT: Turning Pattern Adjusting Knob to
the right until tight will make spray pattern round, or turning left
make spray pattern ellipse.
The spray pattern of the gun is variable from round to flat
with all patterns in between.
NOTE: To reduce over spray and obtain maximum
efficiency, always spray
atomization air pressure.
Fluid (PAINT) ADJUSTMENT: Turn the Paint Adjusting Knob
clockwise will decrease the volume of fluid output and
counter-clockwise will increase fluid output.
6
with the lowest possible
FAULTY SPRAY
PATTER
CAUSE
N
Dried material inside
port "A" restricts
passage of
Greater flow of air
from cleaner side-port
"B" forces fan pattern
in direction of clogged side
Dried material around
the outside of the fluid
nozzle tip at position
"C" restricts
passage of atomizing
air at one point through the
center opening of air nozzle
and results in pattern shown,
this pattern can also be caused
by loose air nozzle.
A split spray or one that is
heavy on each end of a fan
pattern and weak in the middle
is usually caused by
(1) too high an atomization air
pressure, or
(2) by attempting to get too
wide a spray with thin material.
(1) Dried out packing around
material needle valve permits
air to get into fluid passageway.
This results in splitting.
(2) Dirt between fluid nozzle
seat and body or loosely
installed fluid nozzle will make
gun split.
(3) A loose or defective swivel
nut on siphon cup or material
hose can cause spitting.
1/2" Impact Wrench
The Husky 1/2 Impact wrench is supplied with an internal
"
power regulator (36). This tool may be adjusted by rotating the
regulator valve until desired output is achieved. The numbers 1
though 4 on the regulator are only for reference and do not
denote a specific power output. While pushing the regulator
turn to 4 for maximum power and turn to 1 for minimum power.
Power is regulated by pushing the reverse valve (27) to forward
(F) or reverse (R) direction.
Place the socket over the subject nut and depress the trigger to
operate the wrench. Once a bolt or fastener is seated,
impacting for longer than five seconds will cause excessive
wear and damage to the impacting mechanism. If it takes
longer than five seconds to tighten your bolts or fasteners, we
recommend the use of a larger size impact wrench.
Model No. CAT851
( and how to correct it)
CORRECTION
Dissolve material
side-ports with thinner then
air. blow gun clean. Do not poke
into openings with metal
instruments
Remove air nozzle and wipe
off fluid tip, using rag wet
with thinner. Tighten air
the nozzle.
Reducing air pressure will
correct cause (1).
To correct cause (2), open
material control
position by turning to left. At
the same time, turn spray
width adjustment to right.
This will reduce width of
spray, but will correct split
spray pattern.
To
cause
Back
knurled
(E) place two
drops
machine
on packing,
replace nut and tighten with
fingers only. In aggravated
cases, replace packing.
To correct cause
remove fluid nozzle (F),
clean back of nozzle and
nozzle seat in gun body
using rag wet with thinner,
replace nozzle and draw up
tightly against body.
To correct cause (3), tighten
or replace swivel nut. (G).
in
to full
correct
(1).
up
nut
of
oil
(2),