Stanley SLP3 Manual De Instrucciones página 16

Level Beam Accuracy
(Single Beam) - (See fi gure
• Place laser tool as shown with laser ON. Mark point P
N
1
• Rotate laser tool 180° and mark point P
N
2
• Move laser tool close to wall and mark point P
N
3
• Rotate laser tool 180° and mark point P
N
4
• Measure the vertical distance between P
N
5
D and the vertical distance between P
3
• Calculate the maximum offset distance and compare to the
difference of D and D
3
• If the sum is not less than or equal to the calculated
maximum offset distance the tool must be returned to
your Stanley Distributor for calibration.
Maximum Offset Distance:
= 0,2 mm m x (D
Maximum
= 0,0024 in ft x (D
Compare : (See fi gure
D - D
3
Example:
• D = 10 m, D = 0,5 m
1 2
• D = 0,4 mm
3
• D = - 0,6 mm
4
• 0,2 mm m x (10 m - (2 x 0,5 m) = 1,8 mm (maximum
offset distance)
• (0,4 mm) - (- 0,6 mm) = 1,0 mm
• 1,0 mm ≤ 1,8 mm (TRUE, tool is within calibration)
Level Beam Accuracy
(SLP5 only) - (Multiple Beam) - (See fi gure
• Place laser tool as shown with laser ON.
P
1
Mark points P , P , and P
1 2
• Rotate laser tool 90° and mark point P
P
2
• Rotate laser tool 180° and mark point P
P
3
• Measure the vertical distances between the highest
P
4
and lowest points of the group to get D
• Calculate the maximum offset distance and compare to D
16
)
N
.
2
.
4
and P
1
and P to get D
2 4
as shown in the equation.
4
m - (2 x D
1
ft - (2 x D
1
)
N
5
≤ ± Maximum
4
)
P
.
3
.
4
.
5
.
2
• If D
2
maximum offset distance the tool must be returned to
your Stanley Distributor for calibration.
.
1
.
3
Maximum
to get
3
.
4
Example:
• D = 10 m, D
1
• 0,4 mm m x 10 m = 4,0 mm (maximum offset distance)
• 3,0 mm ≤ 4,0 mm (TRUE, tool is within calibration)
m))
2
ft))
2
90° Square Beam Accuracy
(SLP5 only) - (See fi gure
• Place laser tool as shown with laser ON.
R
1
Mark points P
• Rotate laser tool 90° keeping the down laser beam
R
2
aligned with point P
aligned with point P
• Rotate laser tool 180° keeping the down laser beam
R
3
aligned with point P
aligned with point P
• Measure the horizontal distance between points
R
4
P and P
1
distance D
• Calculate the maximum offset distance and compare to
D and D
2
• If D
2
maximum offset distance the tool must be returned to
your Stanley Distributor for calibration.
Maximum
.
2
is not less than or equal to the calculated
Maximum Offset Distance:
= 0,4 mm m x D
= 0,0048 in ft x D
Compare : (See fi gure
D ≤ ± Maximum
2
= 3,0 mm
2
)
R
, P , P , and P
1 2 3 4
and the front laser beam vertically
4
. Mark point P
2
and the front laser beam vertically
4
. Mark point P
3
to get distance D and points P
5 2
.
3
.
3
and D is not less than or equal to the calculated
3
Maximum Offset Distance:
= 0,4 mm m x D
= 0,005 in ft x D
Compare : (See fi gure
D and D ≤ ± Maximum
2 3
m
1
ft
1
)
P
4
.
.
5
.
6
and P to get
1 6
m
1
ft
1
)
R
4
77-318 / 77-319