Park Tool PRS-20 Guia De Inicio Rapido

Team Race Stand
PRS-20 / PRS-21
Park Tool Co.
6 Long Lake Rd. St. Paul, MN 55115 (USA) www.parktool.com
6
7
16
14
5
1
2
4
1
3
20
2
5
21
23
27
24
25
26
PRS-20_PRS-21_instr-parts_1-11-07.indd 1
Park Tool Co.
Ref. No.
1
8
2
9
3
4
12 11
10
5
17
13
6
6
15
7
18
7
8
9
19
10
11
12
13
22
14
23
15
16
17
18
25
24
19
23
19
26
20
21
24
22
23
24
24
25
25
26
26
27
Team Race Stand
PRS-20 / PRS-21
6 Long Lake Rd. St. Paul, MN 55115 (USA) www.parktool.com
Part No. Description
1729A Front Quick Release Assembly
1722A Rear Quick Release Assembly
1728 Slider Tube Weldment
1721 Slider Rear Axle Extension
1706-2 Knob and Shaft
1715-2 Horizontal Beam End Cap
1716R Horizontal Beam Tube (PRS-20 only)
1734R Aluminum Horizontal Beam Tube (PRS-21 only)
1257-2 Saddle Button Head Socket Cap Screw 1/4 - 20 x 3/8"
1711 Bottom Bracket Saddle
1283X Pivot Button Head Socket Cap Screw M10 x 50
1723 Hitch Pin
1724-2 Bracket Washer
1285X Pivot Screw Nylok Nut
1709L Left Upright Bracket
1709R Right Upright Bracket
170A Buckle & Strap Assembly
290 Nylok Nut
1709-2 Upright Bracket Bolt
1708 Upright Tube (PRS-20 only)
1733 Aluminum Upright Tube (PRS-21 only)
1707 Clamping Collar Quick Release Assembly
1701 Upright Sleeve
1705 Yoke Weldment
479-6 Leg Bolt 1/4 - 20 x 2"
1700-3 Leg Tube (PRS-20 only)
1732-3 Aluminum Leg Tube (PRS-21 only)
1215-2 Leg Cap
1216-4 Leg Attachment Cap Screw
480-6 Leg Nylok Nut 1/4 - 20"
Park Tool Co.
6 Long Lake Rd. St. Paul, MN 55115 (USA) www.parktool.com
The PRS-20 Team Race Stand and PRS-21 Super Lite Team Race Stand are compact,
Qty.
folding workstands that securely hold the bike without clamping the frame tubes or
seat post. Used by professional race mechanics around the world.
1
1 ASSEMBLY
1
1
1
2
2
1
1
2
1
1
1
2
2
1
1
1
1
2
2
3
1
1
1
1
1
3
3
4
3
3
3
3
© 2008 Park Tool Co.
® The color BLUE is a registered trademark and trade dress of Park Tool co.
Team Race Stand
PRS-20 / PRS-21
UNFOLDING FOR USE
1. Loosen knob (#5) a yoke (#22). Raise upright tube
(#19) to desired height and tighten knob.
2. Open clamping collar quick release (#20) and lower
collar to yoke. Close quick release.
3. Unfold legs (#24).
4. Pull hitch pin (#11) and unfold horizontal beam tube
(#7). Reinstall hitch pin.
MOUNTING BIKE IN PRS-20/PRS-21
1. Remove front wheel of bike if clamping by front
dropouts. Remove both front and rear wheels if
clamping bike by rear dropouts.
2. Rest bottom bracket shell of bike into saddle (#9) of
PRS-20/21.
3. Loosen knob (#5) on slider (#3). Position slider so
front or rear dropouts of bike fit over slider¹s front or
rear axle. Lock dropouts with front quick release
assembly (#1) or rear quick release assembly (#2) and
tighten knob.
Note: The PRS-20/21's front axle fits standard 100mm
front dropout spacing. The rear axle has a threaded
axle extension (#4) that can be adjusted for 130mm or
135mm dropout spacing. When mounting bike by rear
dropouts, rest chain on axle extension.
4. Secure bottom bracket with retention strap and clip (#16).
5. Loosen knob (#5) at yoke and rotate bike to desired
working position. Tighten knob.
FOLDING FOR STORAGE
1. Pull hitch pin (#11) and fold horizontal beam tube.
Reinstall hitch pin.
2. Open clamping collar quick release (#20) and raise
collar to top of upright. Close quick release.
3. Fold legs (#24).
4. Loosen knob (#5) at yoke (#22) and lower upright.
Tighten knob.
For more information on the PRS-20 and PRS-21,
and for detailed bike repair instructions,
visit: www.parktool.com.
1/11/08 12:50:18 PM