Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Features
This appliance includes some or all of the following features.
1. Handle
2. Flexible hose
3. Bag full indicator
4. On/off switch
5. Speed control selector
6. Cord rewind button
7. Wheels
8. Accessory storage
9. Dustbag access panel
10. Carry handle
11. Suction head
12. Extension tube
13. Parquet floor head
In addition, this appliance is supplied with the following
accessories (fig. A):
14. Crevice tool
15. Brush tool
16. Upholstery brush
Assembly
Fitting the paper dustbag (fig. B and C)
Note: Standing the vacuum cleaner on end may make fitting
the dustbag easier.
Stand the vacuum cleaner on its end (fig. B).
Release the dustbag access panel catch (21) and open
the dustbag access panel (9).
Carefully slide the cardboard flange (19) of the paper
dustbag (18) into the plastic flange.
Close the dustbag access panel (9).
Connecting and disconnecting the hose (fig. C)
To connect the hose:
Insert the hose connector (20) into the inlet of the
appliance until it locks into position.
To disconnect the hose:
Press the inwards on the two clips and pull out the hose.
Mounting the extension tube
Insert the extension tube (12) into the end of the
handle (1).
Mounting the suction head (fig. D)
The suction head (11) allows for vacuuming on carpet and
hard surfaces (e.g. laminate and tiles).
Slide the extension tube (12) into the suction head (11).
To remove the suction head (11), pull the extension
tube (12) from the suction head.
Mounting accessories (fig. D)
Slide the catch (17) forward to open the spring-loaded
accessory storage panel (8).
The crevice tool (14) allows for vacuuming in narrow and
hard-to-reach places. The upholstery brush (16) and the
brush head (15) allow for vacuuming on furniture, blinds,
curtains, windows and stairs.
The accessories can be mounted on the end of the
handle (1) or on the extension tube (12).
Firmly push the accessory onto the end of the
handle (1) or extension tube (12) as required.
To remove an accessory, pull the accessory from
the end of the flexible hose or the extension tube.
When not in use, the accessories can be stored in the
accessory compartment (fig A).
Use
Adjusting the length of the tube (fig. E)
To extend the length of the tube press the adjustment
button (22) and pull out the tube to the required length,
make sure that it clicks into place.
Unwinding and rewinding the cord (fig. F)
The cord rewind button (6) can be operated by hand
or by foot.
Before use, pull a sufficient length of cord from the back
of the appliance.
Plug the appliance into a suitable mains socket.
After use, disconnect the appliance from the mains
socket and press the cord rewind button (6) to store the
cord back into place. Manually guide the cord to make
sure that it does not swing back. Make sure the plug
is correctly located.
Switching on and off (fig. F)
The on/off switch (4) can be operated by hand or foot.
To switch the appliance on, press the on/off switch (4).
To switch the appliance off, press the on/off switch (4)
again.
Adjusting the airflow (fig. F)
Slide the speed control selector (5) to adjust the airflow
as required.
Adjusting the suction head (fig. G)
For vacuuming on carpets, switch the floor surface
selector (23) into the up position (fig. G).
For vacuuming on laminates, tiles, etc., switch the floor
surface selector (23) into the down position.
ENGLISH
7
Publicidad
Tabla de contenido
