Rimage Produce IIIN Guia De Instalacion

Rimage Producer IIIN
® ™
Setup and Installation Guide
Before you begin:
This document describes how to set up your Producer IIIN product. Products in the
Producer IIIN series include the Producer 6100N, Producer 7100N, and Producer
8100N.
This document is intended for people who are familiar with hardware setup, software
installation, and Windows operating systems.
If you do not understand the procedures in this document, ask your computer technician
for help.
Documents referenced in this procedure shipped with your product and are also
available online at www.rimage.com/support. From the Support menu select: Producer
Series > Your Product > User Manuals tab.
-
Important!
•
Read all setup instructions thoroughly before you begin.
•
Save all packing boxes and packing materials for your autoloader and your
printer.

Notes:
•
Your product may not look exactly like the product pictured.
•
The terms "Producer IIIN" and "autoloader" are used through this document to
refer to the products listed above.
•
Unless otherwise indicated, all Windows navigation statements are Windows 7
paths. Other Windows operating system navigation may differ slightly.
# Required tools:
•
Scissors or side cutters
•
Phillips screwdriver
1
Prepare the Producer IIIN
a. Remove all tape from the outside
of the Producer IIIN.
b. Open the door.
c. Remove the protective film from
the inside of the door.
d. Cut the plastic tie wraps (Qty. 2)
from the lift arm.
n
Caution! Do not cut the belt or
the cable!
Tape
e. If you have a Producer 6100N or
8100N, remove the tape from the
disc diverter.
f. Remove the shipping foam
inserted above the carousel.
g. Close the door.
Shipping Foam
2001164_E Copyright © 2009 Rimage Corporation
2
Set up your printer (Everest)
Unpack the Everest printer. Refer to
a.
the label on the Everest printer box.
b. Follow the instructions on the
instruction card on the rear of the
printer.
i.
ii.
c. Open the Everest printer.
i.
ii.
d. Open latches 1, 2, and 3 as indicated by
the arrows.
Tie Wraps
OR
Set up your printer (Prism)
a. Unpack the Prism printer. Refer to the label on the Prism
printer box.

b. Place the printer on the Rimage Producer IIIN so that the
plastic printer feet slide into the slots on the printer plate.
Protective Film
Voltage Switch
Set the AC voltage switch.
Move the shipping screw to the
Instruction
storage position.
Card
Shipping Screw
Press the two side cover latches.
Side Cover Latches
Lower the side cover.
Latch 1
Note: The Prism print ribbon is preinstalled.
Printer Plate
Slots
Remove the plastic packing pieces
e.
(Qty. 2) from inside the printer.
f. Install the print ribbon and retransfer
ribbon. Refer to the instruction label on
the side cover, or to the Rimage Everest
User Guide.
Shipping Screw
Storage Position
g. Place the printer on the Producer IIIN so that the plastic printer feet slide into the
slots on the printer plate.
Printer Plate
Slots
h. Connect the cables.
i. Connect the printer cable from the
Producer IIIN to the printer.
ii. Connect the USB cable from the
Producer IIIN to the printer.
iii. Connect the power cord from the
Producer IIIN to the printer.
Latch 2 Latch 3
c. Connect the cables.
i. Connect the USB cable from the Producer IIIN to the printer.
ii. Connect the printer cable from the Producer IIIN to the printer.
iii. Connect the power cord from the Producer IIIN to the printer.
Press the Prism printer power switch to the On position.
d.

Note: The parallel port is not used.
USB Cable
Plastic Packing Pieces
Printer Cable USB Cable
Power
Cord
Power Cord
Power Switch
Printer Cable
Page 1