Black and Decker BES510 Manual De Instrucciones página 7

6. Shoe
7. 24T TCT saw blade (fitted) for cutting wood
7a. 44T HSS saw blade for cutting thin wood, PVC and
aluminium
8. Saw blade guard
9. Guard handle
10. Saw dust outlet
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped.
Removing and fitting a saw blade (fig. A)
Removing
Keep the spindle lock button (5) depressed and rotate the
u
blade until the spindle lock engages.
Loosen and remove the blade retaining screw (11) by
u
turning it clockwise using the hex key (12) supplied.
Remove the outer washer (13).
u
Remove the saw blade (7).
u
Fitting
Place the saw blade onto the inner flange (14), making
u
sure that the arrow on the blade points in the same direc-
tion as the arrow on the tool.
Fit the outer washer (13) on the spindle, with the raised
u
part pointing away from the saw blade.
Insert the blade retaining screw (11) into the hole.
u
Keep the spindle lock button (5) depressed.
u
Securely tighten the blade retaining screw by turning it
u
counterclockwise using the hex key (12) supplied.
Fitting and removing the parallel fence (fig. B)
The parallel fence is used to saw in a straight line parallel
u
to the edge of the workpiece.
Fitting
Loosen the locking knob (16).
u
Insert the parallel fence (17) through the openings (18).
u
Slide the parallel fence into the desired position.
u
Tighten the locking knob.
u
Removing
Loosen the locking knob.
u
Pull the parallel fence off the tool.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Note: This tool can be used in the right hand or the left hand.
(Original instructions)
Adjusting the depth of cut (fig. C)
The depth of cut should be set according to the thickness of
the workpiece. It should exceed the thickness by approx. 2
mm.
Loosen the knob (20) to unlock the saw shoe.
u
Move the saw shoe (6) into the desired position.
u
The corresponding depth of cut can be read from the
scale (19).
Tighten the knob to lock the saw shoe in place.
u
Switching on and off
To switch the tool on, press the lock-off button (2) and
u
squeeze the on/off switch (1).
To switch the tool off, release the on/off switch.
u
Sawing
Always hold the tool with both hands.
Let the blade run freely for a few seconds before starting
u
the cut.
Apply only a gentle pressure to the tool while performing
u
the cut.
Work with the shoe pressed against the workpiece.
u
Hints for optimum use
As some splintering along the line of cut on the top side of
u
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
Where splintering is to be minimised, e.g. when cutting
u
laminates, clamp a piece of plywood onto the top of the
workpiece.
Using the sight guide (fig. D)
The tool is equipped with a sight guide for straight cutting.
Align the centre of the guide (22) with the cutting line (21).
u
Keep the sight guide aligned with the cutting line while
u
sawing.
Work with the shoe pressed against the workpiece.
u
Dust extraction (fig. E)
An adaptor is provided to connect a vacuum cleaner or dust
extractor to the tool.
Insert the dust extraction adaptor (10a) into the saw dust
u
outlet (10).
Connect the vacuum cleaner hose to the adaptor.
u
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Regularly clean the ventilation slots in your tool using a
u
soft brush or dry cloth.
ENGLISH
7