Storage - Scheppach SG2500i Manual Del Usuario

Ocultar thumbs Ver también para SG2500i:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 66
• Remove the air filter (Fig. 8 Pos. C)
• Clean the filter elements with soapy water. After
rinse the filter elements with clear water and allow to
dry thoroughly before refitting.
• Reassemble in reverse order
m WARNING
NEVER use gasoline or cleaning solvents with a low
flash point to clean the air filter element. A fire or explo-
sion could result.
Note
Never run the engine without or with a damaged air fil-
ter. Dirt gets so into the engine, causing serious engine
damage can occur. In this case, seller, and manufactur-
er disassociate from any warranty.
Check, clean and replace spark plug
Check the spark plug after 10 hours on dirt and grime.
If necessary, clean it with a copper wire brush. Mainte-
nance the spark plug after 50 hours of operation
• Open the spark plug cover (Fig. 9)
• Remove the ignition cable with plug. (Fig. 9 Pos. D)
• Remove any dirt from the base of the spark plug.
• Use the enclosed spark plug wrench to remove the
spark plug.
• Check the spark plug visually. Remove any debris
with a wire brush.
• Look for discoloration on the top of the spark plug.
By default, the color should be bright.
• Check the spark plug gap. An acceptable gap width
is 0.6 to 0.7 mm (Fig. 11)
• Remove the spark plug carefully by hand.
• If the plug has been inserted, tighten them with a
spark plug wrench.
• Attach the spark plug wire with connector on the
spark plug.
NOTE
A loose spark plug can overheat and damage the en-
gine. And over tightening the spark plug can damage
the threads in the cylinder head.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: spark plug
* Not necessarily included in the scope of delivery!
28 | GB
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust. Wipe the equipment
with a clean cloth or clean it with compressed air at
low pressure.
• We recommend that you clean your device after
each use.
• Clean the unit regularly with a damp cloth and some
soft soap. Do not use cleaning agents or solvents;
they may damage the plastic parts of the appliance.
Make sure that no water can get inside the unit.

11. Storage

1.
Perform all general maintenance, which are in the
User's Guide in the Maintenance section.
2.
Let the fuel out of the tank (Use a commercially
plastic fuel pump from the hardware store).
3.
After the fuel is drained, start the machine.
4.
Let the machine in idle speed running until it stops.
That cleans the carburetor from the remaining fuel.
5.
Let the machine cool down. (about 5 minutes)
6.
Remove the spark plug.
7.
Fill a small amount of 2-stroke engine oil into the
firing chamber. Pull out several times the starter
cord gently to wet the internal components with
the oil.
8.
Replace the spark plug.
9.
Clean the outer casing of the machine.
10. Keep the machine on a cold, dry place out of reach
of ignition sources and flammable substances.
Recommissioning
1.
Remove the spark plug.
2.
Pull the starter rope out several times. It cleans the
firing chamber of oil residues.
3.
Clean the spark plug contacts or install a new
spark plug.
4.
Fill the tank.
www.scheppach.com

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

5906226901

Tabla de contenido