Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT SAFETY ADVICE
PRECAUTIONS
This bicycle has been designed and constructed to
provide
maximum
precautions should be taken when using exercise
equipment.
Read
assembling and using the bicycle. The following safety
precautions should also be observed:
1 Keep children away from this equipment at all times.
DO NOT leave them unsupervised in the room where
this bicycle is kept.
2 It can only be used by one person at a time.
3 If you experience dizziness, nausea, chest pains or
any other symptom while using this appliance STOP
the
exercise.
SEEK
IMMEDIATELY
4 Use the appliance on a level, solid surface. DO NOT
use the bicycle outdoors or close to water.
5 Keep your hands well away from any of the moving
parts.
6 Wear clothing suitable for doing exercise. Do not
use baggy clothing that might get caught up in the
bicycle. Always wear running shoes or trainers when
using the machine. Make sure all laces/cords are tied
correctly.
7 This appliance must only be used for the purposes
described in this manual. DO NOT use accessories
that are not recommended by the manufacturer.
8 Do not place sharp objects near the machine.
9 Disabled people should not use the machine without
the assistance of a qualified person or a doctor.
10 Do warm up stretching exercises before using the
equipment.
11 Do not use the bicycle if it is not working correctly.
Caution: Consult your doctor before beginning to
use
the
bicycle.
important for those over 35 or suffering from
health problems.
Keep these instructions safe for future use.
GENERAL INSTRUCTIONS
Carefully read through the instructions contained in
this manual. It provides you with important information
about assembly, safety and use of the machine.
1 This unit has been designed for home use. The
weight of the user must not exceed 190 kg.
2 Parents and/or those responsible for children should
always take their curious nature into account and how
this can often lead to hazardous situations and
behaviour
resulting
circumstances should this appliance be used as a toy.
3 The owner is responsible for ensuring that anyone
who uses the machine is duly informed about the
necessary precautions.
safety.
Nevertheless,
the
whole
manual
MEDICAL
ATTENTION
This
advice
is
especially
in
accidents.
Under
English
ASSEMBLY INSTRUCTIONS
For the assembly of this unit, we recommend the
help of a second person.
certain
Take the unit out of its box and make sure that all of
the pieces are there, Fig.1:
before
1.(1) Main body; (2) Front stabilizer; Rear stabilizer
(3); Front post; (5) Handlebar; (6) Backrest; (7) Saddle
handlebar; (8) Post tube cover; (9) Saddle; (10) Upper
tray; (11) Lower tray; (14) Rear cover of console
bracket; (15) Front cover of console bracket; (16) Left
cover; (17) Right cover; (18) Pedals; (19) Console;
Mains transformer.
Hardware pack containing: (20) Screw M8x82; (21)
Spring
8,5x16x1,5; (23) Screw M8x15; (24) Screw M8x55;
(25) Screw M8x25; (26) Screw M10x112; (27) Flat
washer 10,5x20x2; (28) Nut M10; (29) Screw M5x15;
(30) Screw D5x15; (31) Joint piece for covers; (32)
Screw M4x15; (34) Cap; Wrenches
2. Take hold of the front stabilizer bar fitted with
wheels (2), Fig.2, insert the screws (20), washers
(21), (22) and tighten securely.
Take hold of the rear stabilizer bar (3), Fig.2, insert the
screws (24), washers (21), (22) and tighten securely.
3. FITTING THE BACKREST AND THE SADDLE.-
Attach the backrest (6), as shown in Fig.3, insert the
screws (25) and washers (21), (22) and tighten
securely.
Attach the handlebar (7) to the backrest and insert the
wires through the backrest tube. Insert the screws
(26), the washers (27) and nuts (28), Fig.4. Connect
the handlebar wires with the rail wires. Then insert the
wires to the backrest tube and place the cap (34),
Fig.4.
Attach the saddle (9) as shown in Fig.5, insert the
screws (23).
Attach the side covers (16), (17) using the screws
(32), Fig.6.
To adjust the saddle position pull the handle (6-6),
Fig.13. Place the rail into the correct position and
release the handle.
4. FITTING THE FRONT POST.-
Take hold of the front post (4) and fit the lower tray
(11) and the cover (8) as shown in Fig.7. Connect the
wires of the main body with the wires of the front post,
Fig.7.
Insert the front post (4) onto the boss on the main
no
body.
Insert the screws (23), washers (21), (22), Fig.7, and
tighten securely.
Lower the cover (8) and inser the screws (29), and the
joint (33), Fig.7.
16
MOD. BR1000BM
washer
8,2x16x1,5;
(22)
Flat
washer
Publicidad
