DeWalt D23700 Traducido De Las Instrucciones Originales página 27

DO nOt use this circular saw as a table saw. DO nOt attempt
to cut the workpiece from underneath.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
This circular saw is a professional power tool.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D WALT tool is double insulated in accordance
e
with EN62841; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.

In case of cord or plug replacement the tool must
only be repaired by an authorised service agent or by
qualified electrician.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1.5 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
; the maximum length
2
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Assemble the Blade (Fig. E)
1. Place the inner washer
19
2. Retract the lower blade guard
install the blade 9 and the outer washer
3. Check the direction of rotation of the blade.
4. Thread on the blade clamping screw
the washer in position. Turn clockwise.
5. Press the spindle lock button
until the blade stops rotating.
6. Tighten the blade clamping screw firmly using the wrench.
Depth of Cut Adjustment (Fig. A, B)
1. Loosen the depth adjustment knob
2. Move the shoe 6 to obtain the correct depth of cut.
3. Tighten the depth adjustment knob

WARNING: For optimal results, allow the saw blade to
protrude from the workpiece by about 3 mm (see inset in
figure B).
Bevel Adjustment (Fig. C)
The bevel angle can be adjusted between 0° and 45°.
1. Loosen the bevel adjustment knob
2. Set the bevel angle by tilting the saw shoe
indicates the desired angle on the scale.
3. Tighten the bevel adjustment knob
Shoe Adjustment for 90° Cuts (Fig. A, D)
1. Adjust the saw to 0° bevel.
2. Retract the blade guard using the lever
on the blade side.
3. Loosen the bevel adjustment knob
4. lace a square against the blade
90° setting.
a. Slacken the nut 15 of the stop
b. Adjust the stop 16 as required.
c. Tighten the nut and the adjustment knob
15
Replacing the Saw Blade (Fig. E)
1. Engage the spindle lock button
clamping screw by turning counterclockwise using the
17
hex key supplied with the tool.
2. Retract the lower blade guard
replace the blade . Reinstall the washers 18
9
correct position.
3. Check the direction of rotation of the blade.
4. Thread on the blade clamping screw
the washer in position. Turn clockwise.
5. Press the spindle lock button
until the blade stops rotating.
6. Tighten the blade clamping screw firmly using the wrench.
EnGLIsh
onto the shaft.
8 using the lever 7 and
18 .
17 by hand to hold
4 while turning the spindle
13 .
.
13
.
10
6 until the mark
10 .
and place the saw
7
10 .
9 and shoe 6 to adjust the
16 .
.
10
and unscrew the blade
4
8 using the lever 7 and
in the
19
17 by hand to hold
4 while turning the spindle
25