DeWalt DW770 Traducido De Las Instrucciones Originales página 32

EN G LI S H
Cleaning
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine that it will
operate properly. Ensure that chips, dust or workpiece particle cannot
lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow the
instructions given in section Mounting the saw blade. Remove the
jammed parts and reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
Optional Accessories
WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
E
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Using the Roller Table (fi g. 3–5)
The roller table (pp) makes the handling of large and long pieces of
wood very easy (fig. 5). It can be connected either to the left or to the
right of the machine. The roller table requires the use of the optional
legstand (fig. 3).
WARNING: Assemble the roller table following the
instructions supplied with the legstand.
• Replace the short support bars provided with the legstand with the
irregular rails from the table on the side the table is to be used.
• Follow all instructions provided with the roller table.
RANGE OF SAW BLADES AVAILABLE (RECOMMENDED BLADES)
Type of blade Blade dimensions
(diameter x bore x no. of teeth)
DT4222 series 40 216x30x24
DT4286 series 40 216x30x80
DT4320 series 60 216x30x48
DT4350 series 60 216x30x60
Consult your dealer for further information on the appropriate
accessories.
Protecting the Environment
Separate collection. This product must not be disposed of
with normal household waste.
30
WALT, recommended
E
Usage
For general purpose,
ripping and cross-cutting
of wood and plastics
TCG for use with aluminum
ATB for fine cutting of
manmade and natural
wood
TCG for extra fine cutting
of manmade and natural
wood
Should you find one day that your D
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of
recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
D WALT provides a facility for the collection and recycling of D
E
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D WALT office at the address indicated in this
E
manual. Alternatively, a list of authorised D
full details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
GUARANTEE
D WALT is confident of the quality of its products and offers an
E
outstanding guarantee for professional users of the product.
This guarantee statement is in addition to and in no way
prejudices your contractual rights as a professional user or
your statutory rights as a private non-professional user. The
guarantee is valid within the territories of the Member States of
the European Union and the European Free Trade Area.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your
D WALT tool, simply return it within 30 days, complete with all
E
original components, as purchased, to the point of purchase, for
a full refund or exchange. The product must have been subject
to fair wear and tear and proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your D
the 12 months following purchase, you are entitled to one
service free of charge. It will be undertaken free of charge at
an authorised D WALT repair agent. Proof of purchase must
E
be produced. Includes labour. Excludes accessories and spare
parts unless failed under warranty.
• ONE YEAR FULL WARRANTY •
If your D WALT product becomes defective due to faulty
E
materials or workmanship within 12 months from the date of
purchase, D WALT guarantees to replace all defective parts free
E
of charge or – at our discretion – replace the unit free of charge
provided that:
• The product has not been misused;
• The product has been subject to fair wear and tear;
• Repairs have not been attempted by unauthorised persons;
• Proof of purchase is produced;
• The product is returned complete with all original
components.
If you wish to make a claim, contact your seller or check the
location of your nearest authorised D
the D WALT catalogue or contact your D
E
address indicated in this manual. A list of authorised D
repair agents and full details of our after-sales service is available
on the Internet at: www.2helpU.com.
WALT product needs replacement,
E
WALT
E
WALT repair agents and
E
WALT tool, in
E
WALT repair agent in
E
WALT office at the
E
WALT
E