Bpt Futura X2 Manual De Instrucciones página 5

Buttons lock
Press and hold down button
to pressure for 30 seconds to enable cleaning of the device.
If more than one button is pressed at the same time, or repeatedly by
accident, the buttons lock will be automatically activated for 10 seconds.
The buttons lock is cancelled if there is an incoming call.
Note: Only use soft, dry or slightly damp cloths to clean the terminal;
do not use any chemical products.
Standard functions
Answering a call
When there is a call, at the same time as it starts ringing, the picture coming
in from the entry panel will be displayed.
To answer the call press button
To mute the audio to the entry panel press button .
To open the door of the entry panel displayed, press button
To terminate the call press button
The call will be terminated automatically after 60 seconds.
Note: On some types of system the icon
icon will appear on the screen that warns that the door is open.
Self-connection
To see the picture taken by the entry panel without activating audio com-
munication, press button .
Where there are several entry panels or video cameras connected to the
system, press button again to show in succession the pictures taken
by these devices.
To start audio communication with the entry panel displayed, press button
.
Note: In self-connection mode or with a video call in progress, press
button to save a frame of the picture displayed in the video mail box.
Activating auxiliary commands
Buttons and can be associated to auxiliary commands (switching on stair
light, opening gate, etc.).
The buttons are enabled when communication is active, button can
be enabled even when there is no active communication if the system's
configuration allows it.
Disabling ring tone
To disable the ring tone press button
The ring tone will be disabled for all call types; consequently, the receipt of a
call from the entry panel will ONLY activate the video. To reactivate the ring
tone, press button again.
Intercom
Intercom calls
In systems with several receivers, select the number of the desired receiver
in order to make the call. Press button (LED on) to be able to select
receivers from 5 to 8.
After selecting the desired receiver, the receiver that's calling will emit a line
free tone, while the receiver being called will ring.
To answer the call press button
Transferring a call
With an active communication, select the receiver you wish to transfer the
call to (the receiver that's calling will emit a line free tone, while the receiver
being called will ring).
To answer the call press button
Once audio connection is made with the desired receiver, press
transfer the call.
The receiver that receives the call can also transfer it.
for 3 seconds; the buttons will not respond
.
.
will light up or a special
until the relative LED comes on.
on the receiver being called.
on the receiver being called.
Porter functions
Porter call notification
The porter can send a notification asking to be called back. The notification
is marked by LED Aux2 coming on and remains active until the porter is
called back.
To call the porter press button .
Porter call request
It is possible to send a notification to the porter asking to be called back.
To send the request to the porter press button ; the porter will receive a
notification with the number of the caller.
Panic button function
Press button
.
will come on.
The porter receives a "Panic" notification, along with the caller number, the
LED stays on until the porter makes contact with the receiver.
The "Panic" notification takes priority over all calls.
Alarm signalling
If an alarm device is connected to the receiver's dedicated input, its activation
will cause an alarm notification to be sent to the porter and this signal will
be notified by the receiver in the form of an intermittent acoustic signal for
approximately 10".
Mail box functions
Enabling mail box
Hold down button
show that the function is active.
With the mail box function turned on, when there is a call the receiver takes a
picture of the caller; the flashing
that haven't been displayed yet.
To look at the mail box
Briefly press button
Press button
previous picture; on the bottom right the date and time the picture was
taken is shown.
To delete all the messages in the mail box.
Briefly press button
menu items by pressing button
button to delete all the pictures in the archive.
Device set-up
Briefly press button
menu items by pressing button
to change is shown; press button
button to decrease the value selected; the value entered is confirmed by
going on to the next item on the menu.
to
Note: it is recommended that changes are made to the menu items
while a video call is in progress so as to be able to see the
variations made.
To leave the on-screen menu show the menu item
for at least 1", the receiver will beep and the red LED
for more than 2 seconds; the
icon indicates there are pictures present
to access the archive of stored pictures in the mail box.
to display the next picture and button
to activate the on-screen menu; scroll through the
again until the line is shown
to activate the on-screen menu; scroll through the
repeatedly until the menu item you want
to increase the value selected, press
icon will light up to
to display the
; press
and press button .
5