Intended Use - stayer SCR216W Manual De Instrucciones

This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine's date, check for updates
of our machines on the website: www.grupostayer.com

1. INTENDED USE

This tool has been solely and exclusively designed for:
1. Stationary works on flat and stable surface
2. Working on hard and soft wooden pieces
3. Working on chipboard pieces
4. Working on fiberboard pieces
5. Working on PVC tubes
6. Making straight cuts along the length and width of the
workpiece
7. Making horizontal mitre-cuts between -45º and 45º.
8. Making vertical mitre-cuts between 90º and 45º
Refer to the limits regarding the size of the workpiece on
chapter 11.
2. Unpackaging and assembling
Unpackaging
1. Cut the seal and open the box.
2. Withdraw upper cardboard stoppers
3. Extract the box by firmly grasping the operating head
and the motor body using both hands so as to balance
the weight
4. Extract the box with the accessories
5. Extract the documentation
6. Preserve the cardboard box, the stoppers and the do-
cumentation permanently in an inventoried safe environ-
ment being easily accessible and known to the machine
operator.
Packaging
Operation 1: Securing, folding and fastening the ope-
rating head:
1. Place upper head at horizontally 0º.
2. Place upper head at vertically 90º.
3. Arrange the protector in a manner that it contacts with
the cutting bench.
4. Lower head to the limit and position it to be able to lock
it with the button.
Operation 2: Packaging the machine
1. Locate the cardboard box.
2. Locate documentation.
3. Firmly grasp the machine by its operating head and mo-
tor body.
4. Place the machine over the 4 circular recesses of the
bottom of the box.
5. Store documentation of the machine.
6. Position upper cardboard stoppers.
Close the box and fix it with sealing tape.
ENGLISH
9
3. Setting or fastening the machine in a
stable position
1. The working area where the machine is being arranged
must mandatorily be safe.
2. Place the tool in a stable position on an even surface.
3. Always use the rear support 12.
4. The base of the mitre saw has four holes for firmly fas-
tening the machine to the working bench. It is strongly re-
commended to fix the machine to the bench by means of
the pertinent screws and nuts.
4. Connection to the grid, wiring, fuses,
socket type for the jack and requirements
for grounding
1. To supply electrical power to the machine, connect the
Schuko jack to a standard socket capable of supplying a
minimum of 2000 VA .
2. The internal wiring of the machine is completely termi-
nated so that no wiring is needed when installing it.
3. The machine does not have fuses although the use of
a dedicated magnetothermal switch is recommended as a
protection for the machine.
4. The machine has a class II electrical equipment so that
it does not make use of the grounding of the electrical
installation
5. Illustrated description of functions
1. Angle selector knob.
2. Cutting disc block
3. Unblocking switch for cutting disc
4. Telescopic guide block
5. Head block knob.
6. Disc drop limit regulator.
7. Disc tilt limit regulator angle 0º/45º.
8. Disc tilt limit regulator.
9. Disc tilt limit regulator angle +45º/-45º.
10. Long pieces cutting support insertion.
11. Clamp insertions.
12. Rear support
6. Limitations regarding environmental
conditions
The IP degree of this machine is 20. This machine is pro-
tected against its dangerous parts being accessed by a
finger and against solid foreign particles having diameters
of 12'5 mm and more. This machine does not have any
kind of protection against the entry of water so that its use
in exterior or interior environmental conditions with a risk
of precipitations is forbidden.
9