DeWalt DCS355 Traducido De Las Instrucciones Originales página 44

ENGLISH
with the shaft. Ensure the accessory is oriented
as shown in figure 4.
4. Release the accessory clamp lever.
NOTE: Some accessories, such as scrapers and
blades can be mounted at an angle if required as
shown in figure 5.
INSTALLING/REMOVING SANDING SHEETS (FIG. 6)
A diamond shaped platen uses a hook and loop
adhesion system to attach the sanding sheets. The
platen allows you to use it on large flat surfaces and
tight spots or corners.
1. Attach the sanding platen (w) as described
under Installing/Removing Accessories.
2. Align the edges on the sanding sheet, with
the edge of the sanding platen and press the
sanding sheet (x) onto the platen.
3. Firmly press the base with the sanding sheet
attached against a flat surface and briefly switch
the tool on. This provides for good adhesion
between the platen and the sanding sheet and
also helps to prevent premature wear.
4. When the tip of the sanding sheet becomes
worn, detach the sheet from the platen, rotate
and reapply.
ATTACHING ACCESSORIES USING THE UNIVERSAL
ADAPTER (FIG. 7)
CAUTION: To avoid injury, do not
use any accessory for an application
where the adaptor may fail to hold the
accessory.
CAUTION: Read and follow all
manufacturers' safety warnings for any
accessories used with this tool.
CAUTION: To avoid injury, ensure
adaptor and accessory are securely
tightened.
Non-D WALT accessories can be attached using
E
the universal adaptor.
1. Place the washer (k) on the tool.
2. Place accessory (l) on to washer.
3. Tighten and secure adaptor nut (p) using hex
wrench (r).
Attaching the Cut Guide (fi g. 8–13)
The depth/cut guide allows you to precisely cut
material at a specified depth and more accurately
track a marked cut line.
42
1. Attach the cut guide block (f) by inserting
the accessory tabs (m) on the guide into the
accessory side mount slots (e) on the main
body of the tool.
NOTE: The depth/cut guide can be attached to
either side of the tool.
2. Secure the block to the main body with the
supplied screw (o) and washer (u). Tighten with
the supplied hex wrench (p).
DEPTH GUIDE
This feature allows you to precisely cut material at a
specified depth.
1. Insert the guide arm (g) as shown in figure 9 into
the front slot on the guide block (f).
2. Adjust the length of the guide by pulling out or
pushing inward to achieve the desired cut depth
as shown in figure 10.
3. Secure the guide in place by turning the depth/
cut adjustment knob (n) clockwise. To release
the guide turn the depth/cut adjustment knob
counterclockwise.
CUT GUIDE
This feature allows you to more accurately track a
marked cut line.
1. Insert the guide arm (g) as shown in figure 11
into the slots on the left and right sides of the
guide block (f).
2. Adjust the length of the guide by pulling out or
pushing inward to achieve the desired length as
shown in figure 12.
3. Secure the guide in place by turning the depth/
cut adjustment knob (n) clockwise. To release
the guide turn the depth/cut adjustment knob
counterclockwise.
NOTE: The guide arm can also be placed in the
guard assembly vertically in order to set the height
off a cut. Refer to figure 13.
Attaching the Dust Extraction
Adaptor (fi g. 17)
The Dust Extraction Adaptor allows you to connect
the tool to an external dust extractor, either using
the AirLock™ system (DWV9000-XJ), or a standard
35 mm dust extractor fitment.
1. Attach the dust extraction adaptor (q) by
inserting the tabs (m) in to the accessory side
mount slots (e).
NOTE: The dust extraction adaptor can be
attached to either side of the tool.